Alcatel Unleashed

doublevand981

yep it shows Always the local name (1)pst_cpu20> Ethernet interface setup ======================== Netmask : 255.255.255.192 ============================================================================== | Machine type | Local interface | Name | Address | ===========================================...

doublevand981

doublevand981 wrote: ↑04 Nov 2019 01:46
oldboy wrote: ↑04 Nov 2019 00:08 This is no issue at all, it will always show the name of the local CPU that is running in main mode.

if you do a ifconfig it will show the ip address of the main though
i connect to main role ip address (192.168.1.4). the CPU name show here should be cpu_m

doublevand981

oldboy wrote: ↑04 Nov 2019 00:08 This is no issue at all, it will always show the name of the local CPU that is running in main mode.

if you do a ifconfig it will show the ip address of the main though

i connect to main role ip address (192.168.1.4). the CPU name show here should be cpu_m

doublevand981

Hi all, i having OXE system R12.3 running with Dual CPU-8. i configured for system working with Dual CPU active and test bascul command OK . But whenever i accessed the MAIN CPU, the command promt ONLY show the local name ( it not show Local MAIN name). and tried to test both CPUs as main role still...

doublevand981

Here it is. https://1drv.ms/b/s!AsNSTc6gtb8HgdR69utlcXCEpODbZw?e=jsSuOh Hi Alex, i facing problem related to IO2N card, It's may be failed and don't have replaced card. our system using just 200 extension now (ip phone, dect sets, analog, 40 ibs). Could i delete IO2N board in mgr and let Dual CPU r...

doublevand981

Hi all i want to share my story for you: I upgraded the CPU7 to CPU8 ----WITH OUT any additional cable. 1. i plugged CPU8 to slot 6 and 20 and Did NOT change any cables in backplane. Then just JUST got serial connection for CPU8 on slot 6 ONLY, and CPU8 on slot 20 could not get serial connetions 2. ...

doublevand981

alex wrote: ↑13 Oct 2019 04:12
doublevand981 wrote: ↑12 Oct 2019 19:50
what diffrent between N64 and IO2 signalling mode ?

It's all written in paragraph 14.3 of TC2414.

Could you share me the doc ??

doublevand981

Hi all I had changed the signaling as Alex guide then restart system . the Shelfs still could not up. After that i swap the cards from main shelf and remote shelf then it worked. But for some other remote shelfs i did the same procedure but it still down, even that i saw two INTOF2 cards can see eac...

doublevand981

Just unplug all INTOFs. you can also unplug all boards in peripheral ACTs. Wait till all boards in the main ACT came into service. Then plug one INTOF and wait for one peripheral ACT to start, let them load in one-by-one. It could happen due to heavy load, Did you set your ACT 0 Shelf Address : 0 S...

doublevand981

Hi all i want to share my story for you: I upgraded the CPU7 to CPU8 ----WITH OUT any additional cable. 1. i plugged CPU8 to slot 6 and 20 and Did NOT change any cables in backplane. Then just JUST got serial connection for CPU8 on slot 6 ONLY, and CPU8 on slot 20 could not get serial connetions. Be...

Alcatel Unleashed

Search found 246 matches

Re: DUAL CPU8 not show Local Main name in Main active CPU !

Re: DUAL CPU8 not show Local Main name in Main active CPU !

Re: DUAL CPU8 not show Local Main name in Main active CPU !

DUAL CPU8 not show Local Main name in Main active CPU !

Re: OXE Upgrade R6.2 (CPU7) to R12.2 (CPU8)

Re: CPU8 Blank after BIOS Setup

Re: OXE Upgrade R6.2 (CPU7) to R12.2 (CPU8)

Re: OXE Upgrade R6.2 (CPU7) to R12.2 (CPU8)

Re: OXE Upgrade R6.2 (CPU7) to R12.2 (CPU8)

Re: New CPU8 - LAN / Serial Connection