Search found 901 matches

by devnull
16 Jul 2018 10:48
Forum: OmniSwitch 6560
Topic: loopback0 interface
Replies: 4
Views: 72

Re: loopback0 interface

You have deleted your old loopback0 first?? Have you checked manual (Network Guide) Configuring a Loopback0 Interface Loopback0 is the name assigned to an IP interface to identify a consistent address for network management purposes. The Loopback0 interface is not bound to any VLAN, so it always rem...
by devnull
16 Jul 2018 07:42
Forum: OmniSwitch 6560
Topic: loopback0 interface
Replies: 4
Views: 72

Re: loopback0 interface

Try Loopback0
(it's case sensitive)
Don't understand what you mean with Default Gateway.
You probably need to enable IP Interfaces in some vlans where you need to access the switch from.
Routing is as always
ip static-route 0.0.0.0/0 gateway 192.168.0.100
by devnull
12 Jul 2018 06:39
Forum: OmniSwitch 6900
Topic: Configuring switch as NTP Server
Replies: 2
Views: 82

Re: Configuring switch as NTP Server

See http://www.planetcobalt.net/sdb/ntp_leap.shtml
could occur if the initial synchronization has not happend yet.

Otherwise check the ntp server status
"show ntp server status" -> you are better that stratum 16 i hope?
by devnull
09 Jul 2018 04:44
Forum: OmniSwitch 6850 / 6850E
Topic: router with stacking Alcatel 6850 support
Replies: 1
Views: 59

Re: router with stacking Alcatel 6850 support

As with all LACP/Aggregation the maximum thgroughput per flow is limited to bandwidth of one link. You can max out only when having different communications (per default sorce/dest-mac?) between two hosts it will always be 1G only. Try with 10 hosts at the same time! i don't understand the static ag...
by devnull
22 Jun 2018 07:27
Forum: OmniSwitch 6450
Topic: High memory/CPU utilisation?
Replies: 1
Views: 126

Re: High memory/CPU utilisation?

This is normal. Switch CPU is not a good ping target, Switch does hardware forwarding of traffic, this is not affected by cpu. CPU can be more or less busy depending on SNMP polling, WebUI, Multicast BPDU Routing Protocols Management traffic (ssh/ping/.. ) to the switch Everything that needs the Swi...
by devnull
22 Jun 2018 07:15
Forum: OmniSwitch 6560
Topic: Configur trunk port
Replies: 4
Views: 226

Re: Configur trunk port

As i posted. This is not cisco so you have to add all vlans you want to allow as tagged member. There is no command "switchport mode trunk" which allows all configured vlans automagically. Alcatel does it the otherway round -> enable each vlan you need. More work, but better control. Want to have 3 ...
by devnull
21 Jun 2018 11:44
Forum: OmniSwitch 6560
Topic: Configur trunk port
Replies: 4
Views: 226

Re: Configur trunk port

read manual?
6560 is AOS7/8

So try:
vlan 1 members port 1/1/13-14 tagged
vlan 2 members port 1/1/17 tagged
vlan 3 members 1/1/20 untagged
by devnull
21 Jun 2018 02:16
Forum: OmniSwitch 6450
Topic: Configuring with a script?
Replies: 5
Views: 181

Re: Configuring with a script?

What solution did you use?
by devnull
21 Jun 2018 02:15
Forum: OmniSwitch 6560
Topic: Access the switch using GUI
Replies: 3
Views: 109

Re: Access the switch using GUI

setup an IP address for vlan 1
aaa authentification default "local"

and that should be it
by devnull
20 Jun 2018 09:23
Forum: OmniSwitch 6900
Topic: apply license with virtual chassis running? it's valid.
Replies: 2
Views: 174

Re: apply license with virtual chassis running? it's valid.

you can apply the license while in the vc (if you put all licence for all vc switches in the same file it should update all switches) Licences may require a reboot to become active thou

Go to advanced search