Search found 28 matches

by m00n
11 Feb 2014 05:21
Forum: OmniSwitch 10k
Topic: MC-Lag, problem in layer 3 ecmp
Replies: 0
Views: 1278

MC-Lag, problem in layer 3 ecmp

Hello I have a problem with layer 3 mc-lag fail-over. I did everything like in documentation long time ago, and with many troubleshooting problem still exist. In layer 2 everything work properly, when i put uplink port in down status, then second link is using. BUT when i "killed" one connection bet...
by m00n
11 Feb 2014 05:16
Forum: OmniSwitch 10k
Topic: mc-lag lacp "out of sync" agg down
Replies: 2
Views: 1800

Re: mc-lag lacp "out of sync" agg down

Hi sorry for long delay. maybe you resolv this problem. If i remember properly, i replace lacp protocol with static link aggregation and problem dissapeared.
by m00n
28 Nov 2013 08:37
Forum: 7750 SR
Topic: Redistribute ospf into bgp
Replies: 2
Views: 1959

Re: Redistribute ospf into bgp

anyone ?
by m00n
25 Nov 2013 08:06
Forum: 7750 SR
Topic: Redistribute ospf into bgp
Replies: 2
Views: 1959

Redistribute ospf into bgp

Hello I am totalyy new in Alcatel-Lucent Service router world :) i have expierience in Alcatel-Lucent omniswitches family (os 6400, os6850, os10k) but router cli and configuration issues are different than omniswitches :) So the question is: How redistribute ospf routes to bgp. I am looking for cisc...
by m00n
17 Oct 2013 03:53
Forum: OmniSwitch 6850 / 6850E
Topic: Report loopback detection
Replies: 17
Views: 7712

Re: Report loopback detection

Ok too much emotions was in me :) Loop dont kill all my network, only this aggregation when loop occured, but if it is stack when i have connect servers then i have a problems :) Thx for tip how to reenable port after loop detected. I used this commanf before but dont think about disable/enable port...
by m00n
16 Oct 2013 07:15
Forum: OmniSwitch 6850 / 6850E
Topic: Report loopback detection
Replies: 17
Views: 7712

Re: Report loopback detection

Hello I need advice how to prevent loop in MC-lAG OS10k Environment ? From time to time someone connect dumb L2 switch to network and make loop on that dumb l2 switch. Tried everything, qos policies, loop-detection, bpdu guards and everything what i found here doesn't work. It is realyy disaster bec...
by m00n
08 Feb 2012 09:16
Forum: OmniSwitch 6850 / 6850E
Topic: Cacti monitoring vlan-interfaces
Replies: 1
Views: 2970

Cacti monitoring vlan-interfaces

Hello
Does anyone using cacti to monitor traffic in/out vlan interfaces ? In my case it shows values in bits/second that is no true ofcourse. Whe i try monitor physical interface it works normal.
by m00n
02 Feb 2012 11:50
Forum: OmniSwitch 10k
Topic: mc-lag loop detection
Replies: 1
Views: 1399

mc-lag loop detection

Hello Mc-lag detect loop in my network and bring down aggregate. I have a big problem :/ How can i detect where is problem and resolve where is loop ? Log output Feb 2 14:39:11 (none) local0.info swlogd: mcm loop det info(5) CMM:process_status_cmm@4541: Loop Detected port=2/1 vlan=13 count=1 action=...
by m00n
29 Jan 2012 06:50
Forum: OmniSwitch 10k
Topic: ACL, Simple firewall rules
Replies: 2
Views: 1210

Re: ACL, Simple firewall rules

Problem is solved.
I don't think about getting acces to my internal network (default gateawy, dns servers etc.)

so

Code: Select all

policy condition c3 destination ip 1.1.1.1 source ip 1.1.1.0 mask 255.255.255.0
policy rule r3 condition c3 action allow
solved the problem
by m00n
27 Jan 2012 07:06
Forum: OmniSwitch 10k
Topic: ACL, Simple firewall rules
Replies: 2
Views: 1210

ACL, Simple firewall rules

Hi I want block any incoming traffic from outside to one specific host, but allow him internet access so i need established connection. IN documentation i found example policy condition c1 destination ip 1.1.1.1 established policy condition c2 destination ip 1.1.1.1 policy action drop disposition dr...

Go to advanced search