OC48 not going up

Locked
Titoon
Member
Posts: 2
Joined: 09 Oct 2009 16:39

OC48 not going up

Post by Titoon » 22 Oct 2009 17:27

Hi,

I've got an issue bringing an OC48 link up between two 7750 equipped with iom2-20g + m2-oc48-sfp.
The config of each port is as follows:

Code: Select all

A:7750_A>config>port# info 
----------------------------------------------
        sonet-sdh
            hold-time up 50
            path 
                no shutdown
            exit
        exit
        no shutdown
----------------------------------------------
With the other port clock set to "node". Layer 1 is UP:

Code: Select all

A:7750_A>config>port# show port 10/1/1 

===============================================================================
SONET/SDH Interface
===============================================================================
Description        : 
                     :
Interface          : 10/1/1                 Speed                : oc48        
Admin Status       : up                     Oper Status          : up          
Physical Link      : Yes                    Loopback Mode        : none        
Single Fiber Mode  : No                                                        
APS Group          : none                   APS Role             : none        
Clock Source       : loop                   Framing              : sonet       
Last State Change  : 09/09/2009 13:35:19    Port IfIndex         : 337674240   
Last Cleared Time  : 09/09/2009 19:41:34                                       
J0 String          : 0x01                   Section Trace Mode   : byte        
Rx S1 Byte         : 0x0f                   Rx K1/K2 Byte        : 0x00/0x00   
Rx J0 String (Hex) : 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00       
Cfg Alarm          : loc lrdi lb2er-sf slof slos                           
Alarm Status       :                                                       
Hold time up       : 5000 milliseconds                                     
Hold time down     : 0 milliseconds                                        
                                      
Transceiver Data

Transceiver Type   : SFP                                                      
Model Number       : 3HE00046AAAA03  ALA  IPUIARBDABB                         
TX Laser Wavelength: 1310 nm                Diag Capable         : yes         
Connector Code     : LC                     Vendor OUI           : 00:90:65    
Manufacture date   : 2008/12/14             Media                : SONET/SDH   
Serial Number      : PERXXXX                                                  
Part Number        : FTRJ1421P1BCL-A5                                         
Optical Compliance : OC48-IR-1 GIGE-LX                                        
Link Length support: 20km for SMF;                                            
But PPP won't establish between the two:

Code: Select all

A:7750_A>config>port# show port 10/1/1.sts48 

===============================================================================
Path Info
===============================================================================
Description        : STS48
Admin Status       : up                     Oper Status          : down        
Mode               : network                CRC                  : crc32       
Encap Type         : ppp-auto               Configured MTU       : 9208        
Operational MTU    : 9208                   Operational MRU      : 9206        
Last State Change  : 09/09/2009 19:33:44    Path IfIndex         : 874545153   
Scramble           : false                                                     
Accounting Policy  : None                   Collect-Stats        : Disabled    
Net. Egress Que Pol: default                Load-balance-algo    : default     
Egr. Sched. Pol    : n/a                                                       
Signal Label       : 0xcf                   Rx Signal Label      : 0xcf        
Trace String       : Alcatel 7750 SR                                           
Rx Trace String    : Alcatel 7750 SR                                           
Any clue about what the issue could be ? The "Rx Trace String" is mentioning remote device type.
Some of you might tell me "there's a loop somewhere" but it has already been checked; none found,
software or hardware.

Thanks in advance !

Titoon
Member
Posts: 2
Joined: 09 Oct 2009 16:39

Re: OC48 not going up

Post by Titoon » 27 Oct 2009 01:08

Realized just a few minutes after this post that I had not created any router interface for this physical port... PPP negociation wouldn't complete without an IP on both ends !

Locked

Return to “7750 Service Router”