Outgoing calls from OXO via PRA-T2 card
Posted: 04 Jun 2018 06:30
I have an issue related to outgoing calls from OXO via PRA-T2 card.
I'm connecting the PRA to a E1 card (ETSI PRI) in a MSAN,wjich is connected via SIP to a Lab SIP Server.
The layer1 seems OK, no alarms.
I can make calls from MSAN to OXO, but when I try to call from OXO susbcriber, after the dialling is finished, I get congestion or busy tone immediatelly.
I suspect something is missing in my OXO configuration to allow the outgoing calls. Hope somebody can help.
The current configuration is below.
When I call to number 2200, the call is correctly routed to OXO, and the user 104 rings, and the call is established.
But when I dial from 104 subscriber 02001, which should be translated to 2001, I get busy one.
Installation Numbers Table:
Installation Number: 2
International Prefix 00
International Code 34
Intercity Prefix 02
Intercity Code 02
Recall Prefix (empty)
Alternative System CLIP 2200
Numbering Plans Table:
Internal Numbering Plan
Main Trunk Group Start:0 End:0 Base: ARS NMT:Keep (Is it correct?)
External Numbering Plan
Subscriber Start:100 End:199 Base: 104 NMT:Drop
Subscriber Start:200 End:299 Base: 104 NMT:Drop
Subscriber Start:500 End:525 Base: 500 NMT:Drop
Restricted Public Numbering Plan: EMPTY
Private Numbering Plan: EMPTY
End Of Dialing Table:
Prefix:0 Counter:0 Open Dialing
Subscriber/Basestation List
01-005-01 104 Clasico
01-006-01 105 Clasico
External Lines
List of Access:
02-001-01 T2 P001 30 Channels
Additional details:
Protocol Type: EDSS1
Direction of B-Channel
Incoming:0
Outgoing:0
Bi-directional: 30
Public trunk (Checked)
Fixed TEI: 0
List Of Trunk Groups:
Index 1: 02-001-01 T2 P001 30 Channels
AUTOMATIC ROUTING SELECTION
Automatic Routing: Prefixes
Activation: Yes
Network: pub
Prefix: 02
Ranges: 001 – 010
Substitute: 2 (with the NMT:Keep, the 02 is translated to 2 ?)
TrGrList: 1
Called (ISVPN/H450): het
I'm connecting the PRA to a E1 card (ETSI PRI) in a MSAN,wjich is connected via SIP to a Lab SIP Server.
The layer1 seems OK, no alarms.
I can make calls from MSAN to OXO, but when I try to call from OXO susbcriber, after the dialling is finished, I get congestion or busy tone immediatelly.
I suspect something is missing in my OXO configuration to allow the outgoing calls. Hope somebody can help.
The current configuration is below.
When I call to number 2200, the call is correctly routed to OXO, and the user 104 rings, and the call is established.
But when I dial from 104 subscriber 02001, which should be translated to 2001, I get busy one.
Installation Numbers Table:
Installation Number: 2
International Prefix 00
International Code 34
Intercity Prefix 02
Intercity Code 02
Recall Prefix (empty)
Alternative System CLIP 2200
Numbering Plans Table:
Internal Numbering Plan
Main Trunk Group Start:0 End:0 Base: ARS NMT:Keep (Is it correct?)
External Numbering Plan
Subscriber Start:100 End:199 Base: 104 NMT:Drop
Subscriber Start:200 End:299 Base: 104 NMT:Drop
Subscriber Start:500 End:525 Base: 500 NMT:Drop
Restricted Public Numbering Plan: EMPTY
Private Numbering Plan: EMPTY
End Of Dialing Table:
Prefix:0 Counter:0 Open Dialing
Subscriber/Basestation List
01-005-01 104 Clasico
01-006-01 105 Clasico
External Lines
List of Access:
02-001-01 T2 P001 30 Channels
Additional details:
Protocol Type: EDSS1
Direction of B-Channel
Incoming:0
Outgoing:0
Bi-directional: 30
Public trunk (Checked)
Fixed TEI: 0
List Of Trunk Groups:
Index 1: 02-001-01 T2 P001 30 Channels
AUTOMATIC ROUTING SELECTION
Automatic Routing: Prefixes
Activation: Yes
Network: pub
Prefix: 02
Ranges: 001 – 010
Substitute: 2 (with the NMT:Keep, the 02 is translated to 2 ?)
TrGrList: 1
Called (ISVPN/H450): het