IP Touch 4018 Firmware Update

kati88 · Post by **kati88** » 05 Dec 2015 14:28

Hi,

I would like to update my Alcatel 4018 to the latest firmware in order to change the mode from NOE to SIP. I found the latest firmware upped by another user of this forum (viewtopic.php?f=227&t=14190&hilit=firmw ... 8&start=50) - but if I push everthing in my tftp dir, the phone always says: "bad config file".

What do I have to do to tell the phone to grab the binaries and update/flash itself?

My directory contains:

bin4018
datsip4018
lanpbx.cfg
noesip4018

The lanpbx.cfg conains the following:

Code: Select all

APPLICATION_TYPE=APPL_SIP

Currently on the phone:
SW: 3.60.72
Boot: 3.80.10

Kind regards
kati88

kati88 · Post by **kati88** » 06 Dec 2015 06:43

I have to correct myself: The phone says "bad file content"

tgn · Post by **tgn** » 07 Dec 2015 15:27

is there only one line in the lanpbx.cfg?

The lanpbx.cfg conains the following:
Code: Select all
APPLICATION_TYPE=APPL_SIP

regards...

kati88 · Post by **kati88** » 09 Dec 2015 08:22

Yes, it's the only line

tgn · Post by **tgn** » 12 Dec 2015 13:49

a simple google search with lanpbx.cfg leads me to http://enterprise.alcatel-lucent.com/as ... e-ed02.pdf
(2nd hit)
do you have read it?

regards...

kati88 · Post by **kati88** » 12 Dec 2015 20:50

I've read this pdf and followed the instructions. Tftpd64 shows me that the lanpx.cfg will be transferred and after finishing the phone says "bad file content". I tried different encodings. Always the same.

Guest · Post by **Guest** » 13 Dec 2015 04:14

try to give as firstline:

[CODE]TYPE=A4400 VERSION=1 IP_DOWNLOAD=x.x.x.x IP_CPU1=x.x.x.x[/CODE]

where x.x.x.x is an ip-address for downloading the binaries by tftp.

regards...

tgn · Post by **tgn** » 13 Dec 2015 04:14

try to give as firstline:

Code: Select all

TYPE=A4400 VERSION=1 IP_DOWNLOAD=x.x.x.x IP_CPU1=x.x.x.x

where x.x.x.x is an ip-address for downloading the binaries by tftp.

regards...

kati88 · Post by **kati88** » 13 Dec 2015 09:51

The good part: Thank you for this hint! With this line the main update bin4018 was successful.

Code: Select all

Connection received from 192.168.2.180 on port 1024 [13/12 15:33:25.361]
Read request for file <lanpbx.cfg>. Mode octet [13/12 15:33:25.361]
OACK: <timeout=5,blksize=1428,tsize=68,> [13/12 15:33:25.361]
Using local port 58537 [13/12 15:33:25.361]
<lanpbx.cfg>: sent 1 blk, 68 bytes in 0 s. 0 blk resent [13/12 15:33:25.361]
Connection received from 192.168.2.180 on port 1024 [13/12 15:33:29.358]
Read request for file <noe4018-header>. Mode octet [13/12 15:33:29.358]
File <noe4018-header> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [13/12 15:33:29.358]
Connection received from 192.168.2.180 on port 1024 [13/12 15:33:29.374]
Read request for file <noe4018>. Mode octet [13/12 15:33:29.374]
File <noe4018> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [13/12 15:33:29.374]
Connection received from 192.168.2.180 on port 1024 [13/12 15:33:33.371]
Read request for file <bin4018-header>. Mode octet [13/12 15:33:33.372]
File <bin4018-header> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [13/12 15:33:33.372]
Connection received from 192.168.2.180 on port 1024 [13/12 15:33:33.374]
Read request for file <bin4018>. Mode octet [13/12 15:33:33.375]
OACK: <timeout=5,blksize=1428,tsize=863417,> [13/12 15:33:33.375]
Using local port 58541 [13/12 15:33:33.375]
Peer returns ERROR <Abort transfer.> -> aborting transfer [13/12 15:33:33.642]

The phone says in it's soft-version settings NOE version is unknown and I can't change from NOE to SIP. I think the log above shows why this isn't possible - because the binary for this function is missing. I don't have these header files.

Maybe this user: viewtopic.php?p=89046#p89046 has the nearly same problem? I also tried to rename the "datsip4018" file to "dat4018" in order to avoid the second file not found error in the log. But the phone says s.th. like "incompatible".

kind regards
kati

EDIT:
I startet Netlog to see whats happens on the phone:

Code: Select all

<15> 00:00:05 000-00:00:05.640 MGR    : mgr_startup: init status 3.00 started	192.168.2.180	13/12 16:21:09.637	
<15> 00:00:05 000-00:00:05.640 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:09.637	
<15> 00:00:05 000-00:00:05.640 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:09.637	
<15> 00:00:05 000-00:00:05.640 INIT   : ###########step_initscreen:3/5 config download	192.168.2.180	13/12 16:21:09.637	
<15> 00:00:05 000-00:00:05.640 INIT   : ###########step_initscreen,step:3	192.168.2.180	13/12 16:21:09.652	
<15> 00:00:07 000-00:00:07.640 TFTP   : canditate server 192.168.2.110 / requesting lanpbx.cfg	192.168.2.180	13/12 16:21:11.588	
<15> 00:00:07 000-00:00:07.640 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 TFTP   : option: timeout            5	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 TFTP   : option: blksize            1428	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 TFTP   : option: tsize              68	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 TFTP   : xfer started	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 TFTP   : free memory =   4744784 bytes	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 TFTP   : 1st alloc   =      1428	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 TFTP   : xfer finished	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 INIT   : found 1/0 CS line(s) in lanpbx	192.168.2.180	13/12 16:21:12.205	
<15> 00:00:07 000-00:00:07.640 INIT   : Maincpu IP_CPU changed, flashing new params	192.168.2.180	13/12 16:21:12.221	
<15> 00:00:07 000-00:00:07.650 MGR    : mgr_startup: init status 3.01 success	192.168.2.180	13/12 16:21:12.222	
<15> 00:00:07 000-00:00:07.650 INIT   : CODE binary is invalid -> force download	192.168.2.180	13/12 16:21:12.223	
<15> 00:00:07 000-00:00:07.650 MGR    : mgr_startup: init status 4.00 started	192.168.2.180	13/12 16:21:12.224	
<15> 00:00:07 000-00:00:07.650 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:12.224	
<15> 00:00:07 000-00:00:07.650 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:12.225	
<15> 00:00:07 000-00:00:07.650 INIT   : ###########step_initscreen:4/5 binary download	192.168.2.180	13/12 16:21:12.225	
<15> 00:00:07 000-00:00:07.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:21:12.225	
<15> 00:00:09 000-00:00:09.650 MGR    : mgr_startup: init status 4.38 getting code	192.168.2.180	13/12 16:21:14.188	
<15> 00:00:09 000-00:00:09.650 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:14.188	
<15> 00:00:09 000-00:00:09.650 INIT   : ###########step_initscreen:getting code	192.168.2.180	13/12 16:21:14.188	
<15> 00:00:09 000-00:00:09.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:21:14.188	
<15> 00:00:11 000-00:00:11.650 INIT   : dhs3_get_xxxx: tftp://192.168.2.110:69/noe4018	192.168.2.180	13/12 16:21:16.171	
<15> 00:00:11 000-00:00:11.650 TFTP   : canditate server 192.168.2.110 / requesting noe4018-header	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 TFTP   : recv(    1):   19 ERR(1:File not found)	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 TFTP   : canditate server 192.168.2.110 / requesting noe4018	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 TFTP   : recv(    1):   19 ERR(1:File not found)	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 MGR    : mgr_startup: init status 4.33 file not found	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 INIT   : ###########step_initscreen:file not found	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:11 000-00:00:11.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:21:16.198	
<15> 00:00:13 000-00:00:13.650 MGR    : mgr_startup: init status 4.50 getting load	192.168.2.180	13/12 16:21:18.185	
<15> 00:00:13 000-00:00:13.650 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:18.185	
<15> 00:00:13 000-00:00:13.650 INIT   : ###########step_initscreen:getting load	192.168.2.180	13/12 16:21:18.185	
<15> 00:00:13 000-00:00:13.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:21:18.185	
<15> 00:00:15 000-00:00:15.650 INIT   : dhs3_get_xxxx: tftp://192.168.2.110:69/bin4018	192.168.2.180	13/12 16:21:20.172	
<15> 00:00:15 000-00:00:15.650 TFTP   : canditate server 192.168.2.110 / requesting bin4018-header	192.168.2.180	13/12 16:21:20.178	
<15> 00:00:15 000-00:00:15.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : recv(    1):   19 ERR(1:File not found)	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : canditate server 192.168.2.110 / requesting bin4018	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : option: timeout            5	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : option: blksize            1428	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : option: tsize              863417	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : xfer started	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.650 TFTP   : free memory =   4744784 bytes	192.168.2.180	13/12 16:21:20.475	
<15> 00:00:15 000-00:00:15.660 INIT   : __update_do_check: version 43180	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.660 BCOMPAT: binary is compatible	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.930 INIT   : binary_checksum_bank 0: OK	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.930 INIT   : binary_checksum_bank 1: bad header	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.930 INIT   : cannot update - no rescue binary	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.930 TFTP   : xmit(    1):   20 ERR(0:Abort transfer.)	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.940 MGR    : mgr_startup: init status 4.51 no rescue binary	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.940 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.940 INIT   : ###########step_initscreen:no rescue binary	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:15 000-00:00:15.940 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:21:20.491	
<15> 00:00:17 000-00:00:17.940 INIT   : binary_checksum_bank 1: bad header	192.168.2.180	13/12 16:21:22.781	
<15> 00:00:17 000-00:00:17.940 binary_switch: unable to switch (invalid)	192.168.2.180	13/12 16:21:22.781	
<15> 00:00:17 000-00:00:17.940 DEFENCE: reset__: [27] bootloader_end_job [H] (694 tskinit.c)	192.168.2.180	13/12 16:21:22.781

kati88 · Post by **kati88** » 13 Dec 2015 10:58

I have to correct myself again: I changed the name of "noesip4018" file to "noe4018" and with these changes the netlog looks like this:

Code: Select all

<15> 00:00:05 000-00:00:05.640 MGR    : mgr_startup: init status 3.00 started	192.168.2.180	13/12 16:26:14.871	
<15> 00:00:05 000-00:00:05.640 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:14.871	
<15> 00:00:05 000-00:00:05.640 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:14.871	
<15> 00:00:05 000-00:00:05.640 INIT   : ###########step_initscreen:3/5 config download	192.168.2.180	13/12 16:26:14.871	
<15> 00:00:05 000-00:00:05.640 INIT   : ###########step_initscreen,step:3	192.168.2.180	13/12 16:26:14.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : canditate server 192.168.2.110 / requesting lanpbx.cfg	192.168.2.180	13/12 16:26:16.825	
<15> 00:00:07 000-00:00:07.640 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : option: timeout            5	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : option: blksize            1428	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : option: tsize              68	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : xfer started	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : free memory =   4744784 bytes	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : 1st alloc   =      1428	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 TFTP   : xfer finished	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 INIT   : found 1/0 CS line(s) in lanpbx	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 MGR    : mgr_startup: init status 3.01 success	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 INIT   : CODE binary is invalid -> force download	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 MGR    : mgr_startup: init status 4.00 started	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.640 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.650 INIT   : ###########step_initscreen:4/5 binary download	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:07 000-00:00:07.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:26:16.871	
<15> 00:00:09 000-00:00:09.640 MGR    : mgr_startup: init status 4.38 getting code	192.168.2.180	13/12 16:26:18.840	
<15> 00:00:09 000-00:00:09.640 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:18.840	
<15> 00:00:09 000-00:00:09.640 INIT   : ###########step_initscreen:getting code	192.168.2.180	13/12 16:26:18.840	
<15> 00:00:09 000-00:00:09.640 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:26:18.840	
<15> 00:00:11 000-00:00:11.640 INIT   : dhs3_get_xxxx: tftp://192.168.2.110:69/noe4018	192.168.2.180	13/12 16:26:20.815	
<15> 00:00:11 000-00:00:11.640 TFTP   : canditate server 192.168.2.110 / requesting noe4018-header	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : recv(    1):   19 ERR(1:File not found)	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : canditate server 192.168.2.110 / requesting noe4018	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : option: timeout            5	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : option: blksize            1428	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : option: tsize              1956527	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : xfer started	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 TFTP   : free memory =   4744784 bytes	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.640 INIT   : __update_do_check: version 21110	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.650 INIT   : flash not supported in V21110	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.650 TFTP   : xmit(    1):   20 ERR(0:Abort transfer.)	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.650 MGR    : mgr_startup: init status 4.36 not compatible	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.650 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.650 INIT   : ###########step_initscreen:not compatible	192.168.2.180	13/12 16:26:20.847	
<15> 00:00:11 000-00:00:11.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:26:20.862	
<15> 00:00:13 000-00:00:13.650 MGR    : mgr_startup: init status 4.50 getting load	192.168.2.180	13/12 16:26:22.853	
<15> 00:00:13 000-00:00:13.650 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:22.853	
<15> 00:00:13 000-00:00:13.650 INIT   : ###########step_initscreen:getting load	192.168.2.180	13/12 16:26:22.853	
<15> 00:00:13 000-00:00:13.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:26:22.853	
<15> 00:00:15 000-00:00:15.650 INIT   : dhs3_get_xxxx: tftp://192.168.2.110:69/bin4018	192.168.2.180	13/12 16:26:24.821	
<15> 00:00:15 000-00:00:15.650 TFTP   : canditate server 192.168.2.110 / requesting bin4018-header	192.168.2.180	13/12 16:26:24.837	
<15> 00:00:15 000-00:00:15.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : recv(    1):   19 ERR(1:File not found)	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : canditate server 192.168.2.110 / requesting bin4018	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : option: timeout            5	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : option: blksize            1428	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : option: tsize              863417	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : xfer started	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 TFTP   : free memory =   4744784 bytes	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.650 INIT   : __update_do_check: version 43180	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.660 BCOMPAT: binary is compatible	192.168.2.180	13/12 16:26:25.134	
<15> 00:00:15 000-00:00:15.930 INIT   : binary_checksum_bank 0: OK	192.168.2.180	13/12 16:26:25.149	
<15> 00:00:15 000-00:00:15.930 INIT   : binary_checksum_bank 1: bad header	192.168.2.180	13/12 16:26:25.149	
<15> 00:00:15 000-00:00:15.930 INIT   : cannot update - no rescue binary	192.168.2.180	13/12 16:26:25.149	
<15> 00:00:15 000-00:00:15.930 TFTP   : xmit(    1):   20 ERR(0:Abort transfer.)	192.168.2.180	13/12 16:26:25.149	
<15> 00:00:15 000-00:00:15.930 MGR    : mgr_startup: init status 4.51 no rescue binary	192.168.2.180	13/12 16:26:25.149	
<15> 00:00:15 000-00:00:15.930 INIT   : ############ msg_event_init_status	192.168.2.180	13/12 16:26:25.151	
<15> 00:00:15 000-00:00:15.930 INIT   : ###########step_initscreen:no rescue binary	192.168.2.180	13/12 16:26:25.151	
<15> 00:00:15 000-00:00:15.930 INIT   : ###########step_initscreen,step:4	192.168.2.180	13/12 16:26:25.151	
<15> 00:00:17 000-00:00:17.930 INIT   : binary_checksum_bank 1: bad header	192.168.2.180	13/12 16:26:27.431	
<15> 00:00:17 000-00:00:17.930 binary_switch: unable to switch (invalid)	192.168.2.180	13/12 16:26:27.431	
<15> 00:00:17 000-00:00:17.930 DEFENCE: reset__: [27] bootloader_end_job [H] (694 tskinit.c)	192.168.2.180	13/12 16:26:27.431

I think this line looks interesting:

Code: Select all

<15> 00:00:11 000-00:00:11.650 INIT   : flash not supported in V21110	192.168.2.180	13/12 16:26:20.847

Looking into "noe[sip]4018" with a hex editor I can see that it contains "@[noesip40_2.11.10_09Nov11_14h24".

(I also tried to separate noe[sip]4018 into a header and a body by guessing where the header might end and cutting this into a new file - still unsuccessful and a little bit dangerous)

Alcatel Unleashed

IP Touch 4018 Firmware Update

IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update

Re: IP Touch 4018 Firmware Update