IP Touch 4018 Firmware Update

kati88
Member
Posts: 8
Joined: 05 Dec 2015 11:06

Re: IP Touch 4018 Firmware Update

Post by kati88 » 22 Dec 2015 11:46

I also tried the files from this source: https://github.com/xivo-pbx/xivo-provd- ... gs/pkgs.db - still unlucky.

If I write "APPLICATION_TYPE=APPL_SIP" into the lanpbx file the log looks like this:

Code: Select all

<15> 00:00:07 000-00:00:07.640 INIT   : LANPBX: APPLICATION_TYPE=APPL_SIP ignored	192.168.2.180	22/12 17:27:23.795	
<15> 00:00:07 000-00:00:07.640 INIT   : found 0/0 CS line(s) in lanpbx	192.168.2.180	22/12 17:27:23.795	
<15> 00:00:07 000-00:00:07.640 MGR    : mgr_startup: init status 3.25 bad file content	192.168.2.180	22/12 17:27:23.795	
<15> 00:00:07 000-00:00:07.640 INIT   : ############ msg_event_init_status	192.168.2.180	22/12 17:27:23.795	
<15> 00:00:07 000-00:00:07.640 INIT   : ###########step_initscreen:bad file content	192.168.2.180	22/12 17:27:23.795	
<15> 00:00:07 000-00:00:07.640 INIT   : ###########step_initscreen,step:3	192.168.2.180	22/12 17:27:23.795	
<15> 00:00:11 000-00:00:11.640 MGR    : mgr_startup: init status 3.02 failed	192.168.2.180	22/12 17:27:27.837	
<15> 00:00:11 000-00:00:11.640 INIT   : CODE binary is invalid -> force download	192.168.2.180	22/12 17:27:27.838	
<15> 00:00:11 000-00:00:11.640 MGR    : mgr_startup: init status 4.00 started	192.168.2.180	22/12 17:27:27.838	
<15> 00:00:11 000-00:00:11.640 INIT   : ############ msg_event_init_status	192.168.2.180	22/12 17:27:27.839	
<15> 00:00:11 000-00:00:11.640 INIT   : ###########step_initscreen:failed	192.168.2.180	22/12 17:27:27.839	
<15> 00:00:11 000-00:00:11.640 INIT   : ###########step_initscreen,step:3	192.168.2.180	22/12 17:27:27.840	
<15> 00:00:11 000-00:00:11.660 INIT   : ############ msg_event_init_status	192.168.2.180	22/12 17:27:27.840	
<15> 00:00:11 000-00:00:11.660 INIT   : ###########step_initscreen:4/5 binary download	192.168.2.180	22/12 17:27:27.841	
<15> 00:00:11 000-00:00:11.660 INIT   : ###########step_initscreen,step:4	192.168.2.180	22/12 17:27:27.842	
<15> 00:00:13 000-00:00:13.640 MGR    : mgr_startup: init status 4.38 getting code	192.168.2.180	22/12 17:27:29.781	
<15> 00:00:13 000-00:00:13.640 INIT   : ############ msg_event_init_status	192.168.2.180	22/12 17:27:29.781	
<15> 00:00:13 000-00:00:13.640 INIT   : ###########step_initscreen:getting code	192.168.2.180	22/12 17:27:29.781	
<15> 00:00:13 000-00:00:13.640 INIT   : ###########step_initscreen,step:4	192.168.2.180	22/12 17:27:29.781	
<15> 00:00:15 000-00:00:15.640 INIT   : dhs3_get_xxxx: tftp://192.168.2.110:69/noe4018	192.168.2.180	22/12 17:27:31.756	
<15> 00:00:15 000-00:00:15.640 TFTP   : canditate server 192.168.2.110 / requesting noe4018-header	192.168.2.180	22/12 17:27:31.771	
<15> 00:00:15 000-00:00:15.640 TFTP   : elected server is 192.168.2.110	192.168.2.180	22/12 17:27:31.787	
<15> 00:00:15 000-00:00:15.640 TFTP   : recv(    1):   19 ERR(1:File not found)	192.168.2.180	22/12 17:27:31.787	
<15> 00:00:15 000-00:00:15.640 TFTP   : canditate server 192.168.2.110 / requesting noe4018	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.640 TFTP   : elected server is 192.168.2.110	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.640 TFTP   : option: timeout            5	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.640 TFTP   : option: blksize            1428	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.640 TFTP   : option: tsize              1956527	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.640 TFTP   : xfer started	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.640 TFTP   : free memory =   4744000 bytes	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.650 INIT   : __update_do_check: version 21110	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.650 INIT   : flash not supported in V21110	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.650 TFTP   : xmit(    1):   20 ERR(0:Abort transfer.)	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.650 MGR    : mgr_startup: init status 4.36 not compatible	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.650 INIT   : ############ msg_event_init_status	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.650 INIT   : ###########step_initscreen:not compatible	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:15 000-00:00:15.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	22/12 17:27:31.802	
<15> 00:00:17 000-00:00:17.650 MGR    : mgr_startup: init status 4.50 getting load	192.168.2.180	22/12 17:27:33.789	
<15> 00:00:17 000-00:00:17.650 INIT   : ############ msg_event_init_status	192.168.2.180	22/12 17:27:33.789	
<15> 00:00:17 000-00:00:17.650 INIT   : ###########step_initscreen:getting load	192.168.2.180	22/12 17:27:33.789	
<15> 00:00:17 000-00:00:17.650 INIT   : ###########step_initscreen,step:4	192.168.2.180	22/12 17:27:33.789	
<15> 00:00:19 000-00:00:19.650 INIT   : dhs3_get_xxxx: tftp://192.168.2.110:69/bin4018	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : canditate server 192.168.2.110 / requesting bin4018-header	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : recv(    1):   19 ERR(1:File not found)	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : canditate server 192.168.2.110 / requesting bin4018	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : elected server is 192.168.2.110	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : option: timeout            5	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : option: blksize            1428	192.168.2.180	22/12 17:27:36.081	
<15> 00:00:19 000-00:00:19.650 TFTP   : option: tsize              863417	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.650 TFTP   : xfer started	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.650 TFTP   : free memory =   4744000 bytes	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.650 INIT   : __update_do_check: version 43180	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.650 BCOMPAT: binary is compatible	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.930 INIT   : binary_checksum_bank 0: OK	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.930 INIT   : binary_checksum_bank 1: bad header	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.930 INIT   : cannot update - no rescue binary	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.930 TFTP   : xmit(    1):   20 ERR(0:Abort transfer.)	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.930 MGR    : mgr_startup: init status 4.51 no rescue binary	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.930 INIT   : ############ msg_event_init_status	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.930 INIT   : ###########step_initscreen:no rescue binary	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:19 000-00:00:19.940 INIT   : ###########step_initscreen,step:4	192.168.2.180	22/12 17:27:36.097	
<15> 00:00:21 000-00:00:21.930 INIT   : binary_checksum_bank 1: bad header	192.168.2.180	22/12 17:27:38.368	
<15> 00:00:21 000-00:00:21.930 binary_switch: unable to switch (invalid)	192.168.2.180	22/12 17:27:38.383	
<15> 00:00:21 000-00:00:21.930 DEFENCE: reset__: [27] bootloader_end_job [H] (694 tskinit.c)	192.168.2.180	22/12 17:27:38.383	
Giving up seems to be the only solution for this problem :D

ahmedfahmey
Member
Posts: 4
Joined: 02 May 2016 06:20

Re: IP Touch 4018 Firmware Update

Post by ahmedfahmey » 05 May 2016 04:10

finally i have the solution just let me know if you still need it. and anyway i will try to collect all files, commands and configs then i will make a full post ASAP

User avatar
cavagnaro
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 7001
Joined: 14 Sep 2005 19:45
Location: Brasil, Porto Alegre
Contact:

Re: IP Touch 4018 Firmware Update

Post by cavagnaro » 05 May 2016 12:19

Thanks a lot for willing to provide the solution as well.
I am sure that will help others.


Enviado de meu E6633 usando Tapatalk
Ignorance is not the problem, the problem is the one who doesn't want to learn

OTUC/ICS ACFE/ACSE R3.0/4.0/5.0/6.0
Certified Genesys CIV 8.5
Certified Genesys Troubleshooting 8.5
Certified Genesys BEP 8.x
Genesys Developer

kati88
Member
Posts: 8
Joined: 05 Dec 2015 11:06

Re: IP Touch 4018 Firmware Update

Post by kati88 » 10 May 2016 09:21

I'm still interested in a solution :)

okin1980
Member
Posts: 1
Joined: 17 May 2016 09:34

Re: IP Touch 4018 Firmware Update

Post by okin1980 » 17 May 2016 11:31

ahmedfahmey wrote:finally i have the solution just let me know if you still need it. and anyway i will try to collect all files, commands and configs then i will make a full post ASAP
Hi,

Can you please post the solution if you have it?

Thanks a lot

rockie88
Member
Posts: 3
Joined: 10 Aug 2016 13:15

Re: IP Touch 4018 Firmware Update

Post by rockie88 » 12 Aug 2016 14:24

Hi guys any update on this i was trying to update also my 4018 to latest ver. to enable sip but no luck i followed all the guide here and download update files but the phone keep saying "bad file content" . thanks for sharing ideas.

ahmedfahmey
Member
Posts: 4
Joined: 02 May 2016 06:20

Re: IP Touch 4018 Firmware Update

Post by ahmedfahmey » 30 Aug 2016 05:43

Dear All

sorry for beeing late

to update your iptouch 4018 follow the following steps

1- prepare a cross cable
2- install a tftp server ( i used solarwinds tftp server )
3- copy all files to the tftp root folder
4- edit the sipconfig file
5- configure your set ip parameters
6- change restrict vlan to "no"
7- change vlan to your vlan
8- change tftp server 1 & 2 to the pc ip ( tftp server ip )
9- restart your set ( you will see that it's updating )
10- after doing that turnoff the set then connect it to computer by cross cable
11- start the set in industrial mode by holding ( i + 1 + 2 + 3 ) while starting the set & release all buttons when leds lights
12- set your pc ip to 192.168.1.6
13- telnet 192.168.1.1
14- type "verswitch" then press "Enter"
15- restart the set
16- while restarting press ( i + # ) to enter configuration mode
17- go to software info
18- now you can change NOE to SIP
19- after changing to SIP restart the set after connecting normally to your network with the permanent network settengs
20- make sure that your tftp server is working & all files are in the tftp root folder

i think it's ok now set updated & you can connect iptouch to freepbx or any SIP pbx

ahmedfahmey
Member
Posts: 4
Joined: 02 May 2016 06:20

Re: IP Touch 4018 Firmware Update

Post by ahmedfahmey » 19 Sep 2016 05:41

after upgrading & connecting successfully to Freepbx i got a new issue which is : after booting the device it's registering normally without any issues but after a while it losing the registration and then i have to restart to get it registered again.

User avatar
cavagnaro
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 7001
Joined: 14 Sep 2005 19:45
Location: Brasil, Porto Alegre
Contact:

Re: IP Touch 4018 Firmware Update

Post by cavagnaro » 19 Sep 2016 10:16

Maybe it is not receiving the ACK and doing over and over. You will need to see your sip switch logs

Enviado de meu E6633 usando Tapatalk
Ignorance is not the problem, the problem is the one who doesn't want to learn

OTUC/ICS ACFE/ACSE R3.0/4.0/5.0/6.0
Certified Genesys CIV 8.5
Certified Genesys Troubleshooting 8.5
Certified Genesys BEP 8.x
Genesys Developer

rockie88
Member
Posts: 3
Joined: 10 Aug 2016 13:15

Re: IP Touch 4018 Firmware Update

Post by rockie88 » 01 Nov 2016 23:42

Hi Mr.Ahmedfahmey,

is it possible to share to us the firmware file that you used.

thanks
ahmedfahmey wrote:Dear All

sorry for beeing late

to update your iptouch 4018 follow the following steps

1- prepare a cross cable
2- install a tftp server ( i used solarwinds tftp server )
3- copy all files to the tftp root folder
4- edit the sipconfig file
5- configure your set ip parameters
6- change restrict vlan to "no"
7- change vlan to your vlan
8- change tftp server 1 & 2 to the pc ip ( tftp server ip )
9- restart your set ( you will see that it's updating )
10- after doing that turnoff the set then connect it to computer by cross cable
11- start the set in industrial mode by holding ( i + 1 + 2 + 3 ) while starting the set & release all buttons when leds lights
12- set your pc ip to 192.168.1.6
13- telnet 192.168.1.1
14- type "verswitch" then press "Enter"
15- restart the set
16- while restarting press ( i + # ) to enter configuration mode
17- go to software info
18- now you can change NOE to SIP
19- after changing to SIP restart the set after connecting normally to your network with the permanent network settengs
20- make sure that your tftp server is working & all files are in the tftp root folder

i think it's ok now set updated & you can connect iptouch to freepbx or any SIP pbx

Post Reply

Return to “ipTouch (40x8) issues and tricks”