Switch could nto boot - USDone

Post Reply
TienTon
Member
Posts: 1
Joined: 21 Nov 2019 21:50

Switch could nto boot - USDone

Post by TienTon » 21 Nov 2019 23:40

When i try to start the switch 6400-P48. It was stuck as below.
Someone can help me please.


U-Boot (6.4.3.565.R01) (for OS6400, OS6850, and OS6855 platforms) (Jun 24 2010 - 04:04:21)

MPC8247 Reset Status: External Soft, External Hard

MPC8247 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666

CPU: MPC8247 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS6400 (Garuda)
I2C: ready
DRAM: 256 MB
FLASH: 128 MB
No environment variables found, using defaults

In: serial
Out: serial
Err: serial

No ethernet found.
Hit any key to stop autoboot: 0
## Booting image at ff900000 ...
Image Name: miniboot-6.4.3.565.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 1006719 Bytes = 983.1 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Ethernet MAC address not copied to NV RAM
Loading .text @ 0x01000000 (1609912 bytes)
Loading .rodata @ 0x011890b8 (345303 bytes)
Loading .data @ 0x011dd590 (140060 bytes)
Clearing .sbss @ 0x011ff8b0 (1676 bytes)
Clearing .bss @ 0x01200000 (1620268 bytes)
## Using bootline (@ 0x4200): tffs(0,0)lanswitch:default h=192.168.10.1 e=192.168.10.1:ffffff00 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff f=0x0
## Starting vxWorks at 0x01000000 ...
USB2 Host Stack Initialized.
USB Hub Driver Initialized
USBD Wind River Systems, Inc. 562 Initialized
M824xHCI Controller found.
Waiting to attach to USBD...Done.
0xffffde0 (tRootTask): usbBulkDevInit() returned OK
usbCbiUfiDevInit() returned OK
CBI Class Driver Successfully Initialized

CS EEPROM Module ID: 42012286 , System type : 48 port 1000Base-T,with 4 combo ports,Stacking - Garuda


TFFS detected, mounting TFFS file system

Adding 5586 symbols for standalone.


Boot parameters are:

'tffs(0,0)lanswitch:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.181 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff'


AOS miniboot version: 6.4.3.565.R01
VxWorks (for Freescale MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Jun 24 2010, 04:36:06.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Freescale MPC8248. Processor #0.
Memory Size: 256 MBytes. BSP version 1.2/1.

Portions of code copyrighted by Agranat Systems, Inc. All Rights reserved
Portions of code copyrighted by Alcatel Internetworking, Inc. 1994-2010. All Rights reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999. All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991. All rights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000. All rights reserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999. All Rights reserved
Portions of code copyrighted by RSA Security, Inc. All Rights reserved
Portions of code copyrighted by Sun Microsystems, In
c. All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc. All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


Running fsck ....
/flash/ - Volume is OK
Attempting to load from the CERTIFIED directory...
Loading kernel from '/flash/certified/Gos.img'...
6530400
Loaded 'alcatelNetworking_kernel.lnk' from '/flash/certified/Gos.img'.
Starting at 0x100000...

USDone.

Post Reply

Return to “OmniSwitch 6400”