Hi, has a way to show the channel occupations on OXO with PCM-R2,
i need see total channels usage, and information when all channels are busy.
Thanks
OXO PCM-R2 Usage
-
- Member
- Posts: 7
- Joined: 10 Oct 2014 10:31
- Location: Santa Catarina - Brazil
- Contact:
Re: OXO PCM-R2 Usage
Hi
You should create a resource key in add-on module to see channel by channel. It is the only way I know.
Best regards.
You should create a resource key in add-on module to see channel by channel. It is the only way I know.
Best regards.
Enio Eltz Filho
ACFE OXE R12
ACFE OXO C R3
ACFE OXE R12
ACFE OXO C R3
Re: OXO PCM-R2 Usage
Hi, you need to do as Enio says above, but assign each channel as 'special physical address'
cheers
cheers
Re: OXO PCM-R2 Usage
30 key !
stronge why a simple command is not avalaible as oxe .
have you seen in sysytem docf or last R
stronge why a simple command is not avalaible as oxe .
have you seen in sysytem docf or last R
Re: OXO PCM-R2 Usage
Hi Haroun
There is no command line in OXO as in OXE. At least for installer level. Everything is done in graphical OMC, where there is no monitoring for PCM-R2.
Best regards.
There is no command line in OXO as in OXE. At least for installer level. Everything is done in graphical OMC, where there is no monitoring for PCM-R2.
Best regards.
Enio Eltz Filho
ACFE OXE R12
ACFE OXO C R3
ACFE OXE R12
ACFE OXO C R3
-
- Member
- Posts: 7
- Joined: 10 Oct 2014 10:31
- Location: Santa Catarina - Brazil
- Contact:
Re: OXO PCM-R2 Usage
Thanks for reply.enio.eltz wrote:Hi
You should create a resource key in add-on module to see channel by channel. It is the only way I know.
Best regards.
you can help me to create this resource key?
Thanks.
Re: OXO PCM-R2 Usage
I need to know which command to use to monitor the performance of frame
Re: OXO PCM-R2 Usage
Hi Guys,
You can also use 'metering' to check the occupation of your lines.
Just activate the metering over IP, install an Office Link Driver on your network and load the data to Excel.
You can filter on the moment and check how many simultaneous external calls were made...
Lots of fun
Creating the resource keys:
* Go to the details of your phone and select 'Keys'
* Click on the key and make it a Ressource Key - Special Phys. Access
* Select in the part below one of the lines
--> Make keys for every ISDN Trunk available.
Now you can monitor if an ISDN Trunk is used or not (you can't check if both channels are used though).
Good luck
Greets,
Koen
You can also use 'metering' to check the occupation of your lines.
Just activate the metering over IP, install an Office Link Driver on your network and load the data to Excel.
You can filter on the moment and check how many simultaneous external calls were made...
Lots of fun
Creating the resource keys:
* Go to the details of your phone and select 'Keys'
* Click on the key and make it a Ressource Key - Special Phys. Access
* Select in the part below one of the lines
--> Make keys for every ISDN Trunk available.
Now you can monitor if an ISDN Trunk is used or not (you can't check if both channels are used though).
Good luck
Greets,
Koen
If I'm ever on life support, unplug me. Then plug me back in, see if that works...