PowerCPU EE R10 not boot up

doublevand981
Member
Posts: 230
Joined: 09 Apr 2009 21:38
Contact:

PowerCPU EE R10 not boot up

Post by doublevand981 » 28 Jul 2017 22:12

Hi ALL,

I having OXO system running R10. But now it was failed to start .
i reloaded system by lola successful (R103_041_001). but switch back to normal mode the system still could not startup .

Pls help me to fix it !


below is V24 output:

U-Boot 1.3.0-rc3 (Nov 26 2015 - 16:16:13) 3EH30350ABAJ bootl100/001.009

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU: e300c4, MPC8377, Rev: 21 at 799.999 MHz, CSB: 399 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 512 MB
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: High-capacity, 4bit-buswidth mode
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
PowerCPU in CPE Mode
## Booting image at ff837e6c ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 10092 Bytes = 9.9 kB
Load Address: 00200000
Entry Point: 00201d24
Verifying Checksum ... OK
OK
DIP switch: 0x0f
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu 0 Hit any key to stop autoboot: 0
## Booting image at ff83a618 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2850 Bytes = 2.8 kB
Load Address: 00200000
Entry Point: 00200750
Verifying Checksum ... OK
OK
Watchdog Started
Waiting for PHY auto negotiation to complete...... TIMEOUT !
TSEC0: No link.
Waiting for PHY auto negotiation to complete...... TIMEOUT !
TSEC1: No link.

Using TSEC0 device
BOOTP broadcast request 1 in progress ---> 00:80:9f:be:62:41

Using TSEC0 device
BOOTP broadcast request 2 in progress ---> 00:80:9f:be:62:41

Using TSEC0 device
BOOTP broadcast request 3 in progress ---> 00:80:9f:be:62:41

Using TSEC0 device
BOOTP broadcast request 4 in progress ---> 00:80:9f:be:62:41

Using TSEC0 device
BOOTP broadcast request 5 in progress ---> 00:80:9f:be:62:41

Retry count exceeded; giving up

270 bytes read
Refreshing Watchdog... Watchdog Refreshed
## Executing script at 00100000

1967997 bytes read
Refreshing Watchdog... Watchdog Refreshed

6194511 bytes read
Refreshing Watchdog... Watchdog Refreshed
## Booting image at 00800000 ...
Image Name: Linux-2.6.29.6-rt23-026.003
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1967933 Bytes = 1.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00e00000 ...
Image Name: PowerPC_RAMdisk
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 6194447 Bytes = 5.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt at 0x450000
Loading Ramdisk to 0f9b5000, end 0ff9d50f ... OK
setup_arch: bootmem
ale837x_powercpu_setup_arch()
arch: exit
Last edited by doublevand981 on 29 Jul 2017 07:18, edited 1 time in total.

doublevand981
Member
Posts: 230
Joined: 09 Apr 2009 21:38
Contact:

Re: PowerCPU EE R10 not boot up

Post by doublevand981 » 29 Jul 2017 07:17

here is my log file . The system Reboot infinite
You do not have the required permissions to view the files attached to this post.

HUSSAINQCS
Member
Posts: 290
Joined: 21 Jan 2017 02:57

Re: PowerCPU EE R10 not boot up

Post by HUSSAINQCS » 29 Jul 2017 11:42

What is the led indication of the Power CPU ?

Is something done at the OXO side why system not coming up ?

doublevand981
Member
Posts: 230
Joined: 09 Apr 2009 21:38
Contact:

Re: PowerCPU EE R10 not boot up

Post by doublevand981 » 29 Jul 2017 21:41

The Fan led is off
The cpu led is green

Nothing happen at oxo side

ltatge
Member
Posts: 83
Joined: 19 Sep 2012 15:49

Re: PowerCPU EE R10 not boot up

Post by ltatge » 30 Jul 2017 17:36

Just a thought, have you checked jumper on PowerCPU after LoLa? Is jumper in correct position?

Regards LT

doublevand981
Member
Posts: 230
Joined: 09 Apr 2009 21:38
Contact:

Re: PowerCPU EE R10 not boot up

Post by doublevand981 » 30 Jul 2017 21:06

I changed back to normal position after LOLA .

doublevand981
Member
Posts: 230
Joined: 09 Apr 2009 21:38
Contact:

Re: PowerCPU EE R10 not boot up

Post by doublevand981 » 30 Jul 2017 22:34

i would like to attach here the console trace on V24 port
You do not have the required permissions to view the files attached to this post.

ltatge
Member
Posts: 83
Joined: 19 Sep 2012 15:49

Re: PowerCPU EE R10 not boot up

Post by ltatge » 31 Jul 2017 03:22

Try other PowerCPU, If same issue load software version new from Businessportal. If not, maybe a hardware issue with the board.

ltatge
Member
Posts: 83
Joined: 19 Sep 2012 15:49

Re: PowerCPU EE R10 not boot up

Post by ltatge » 31 Jul 2017 03:26

OXO try to take into service DSP and fails.
See console trace:

=============================================================
=> PANIC RESET in cmvision.c line 6645 cause : CTRL DSP (80,00) : RES KO
==============================================================

May be a hardware fault.

doublevand981
Member
Posts: 230
Joined: 09 Apr 2009 21:38
Contact:

Re: PowerCPU EE R10 not boot up

Post by doublevand981 » 07 Aug 2017 02:53

Hi all,

i tried to reload software R103_039_001 and then system worked. i changed ip address and restore database then system worked well.
after some days turn off power and now turn it on they system failed again, boot infinite ( ip address back to default 192.168.92.246)

any pro can help me pls ?

Post Reply

Return to “MAIN”