VPU6 *** WARNING !! PCM System Clock Not Present ***

[mejust]

GUYS IM STuck and I dont know what eles to do.

I just installed a new harddrive on a VPU6 board and Installed 4635V .
The Installation went OK .
After reboot through EPROM after testes I get an error :

Timer Test......................................... PASSED

*** WARNING !! PCM System Clock Not Present ***
*** WARNING !! PCM Dependent Tests May Fail ***
*** WARNING !! Board Is Not Able To Boot ***

So the Board Never Boots

THis is my first 4635 installation so I dont know how to solve this problem.

IF I Boot from HardDisk I get this error :

LILO boot:
Loading linux
Error 0x80

I I boot from Epprom I get the PCM clock error

Im using a ACT for testes with only the VPU6 and no CPU.

Can Someone Help me .

Thks in Advance

Alcatel 4635
Prom Resident Test Demon, Integrated Version

Board Self-Test Status:

CPU Test........................................... PASSED
Console Test....................................... PASSED
Data/Stack RAM Test................................ PASSED
Scrubbing all "known" DRAM memory ..... (00000000-04000000)
C67 test nb# 0 enabled
C67 test nb# 1 enabled
C67 test nb# 2 enabled
C67 test nb# 3 enabled
C67 test nb# 4 enabled
C67 test nb# 5 enabled
C67 test nb# 6 enabled
C67 test nb# 7 enabled
Timer Test......................................... PASSED

*** WARNING !! PCM System Clock Not Present ***
*** WARNING !! PCM Dependent Tests May Fail ***
*** WARNING !! Board Is Not Able To Boot ***

Copyright 1994-2006 Alcatel
System CPU PROM Version: e108VPU5 (Oct 31, 2006 15:41:55)

Board Type is: VPU5
VP_DIAG: RUN *
Display (But NOT Execute) Self-Test Status......... (00) PASSED
DRAM Walking 1s DWORD Test......................... (33) PASSED
DRAM 3Par DWORD Test Executed From DRAM............ (7D) PASSED
Write/Verify Misc Registers........................ (2F) PASSED
Ethernet Test...................................... (74) PASSED
IPoC Controller Test............................... (4A) PASSED
IDE Disk Configuration............................. (50) STARTED
X.
IDE Disk Configuration............................. (50) PASSED
IDE Disk Drive Diagnostic.......................... (4D) PASSED
IDE Disk Read Test................................. (4E) PASSED
Crystal-1 Chip Test................................ (56) STARTED
*56/1* Sub-Test #00: C1-NV Register Reset Values failed!
Crystal-1 Chip Test................................ (56) FAILED ***
C67 DSP Functional Test............................ (20) PASSED
Watch Dog Timer.................................... (5F) PASSED
*** ERROR(s) OCCURRED ***

*** WARNING !! PCM System Clock Not Present ***
*** WARNING !! PCM Dependent Tests May Fail ***
*** WARNING !! Board Is Not Able To Boot ***

Please select from the following:

B Boot the System
^DB Boot the System (clear autoboot, set SRAM=0xFF)
^DD Run Diagnostics Interactively

Selection-> ^
Please select from the following:

B Boot the System
^DB Boot the System (clear autoboot, set SRAM=0xFF)
^DD Run Diagnostics Interactively

Selection-> D
Please select from the following:

B Boot the System
^DB Boot the System (clear autoboot, set SRAM=0xFF)
^DD Run Diagnostics Interactively

Selection-> B

WARNING !! RESETTING and RESTARTING VPU5 Board, due to:
"Can't IPL CPU w/diagnostic failures"
(initiated by "ci module")

[alex]

You should have CPU with telephony running for VPU to start properly.

*** WARNING !! PCM System Clock Not Present ***
*** WARNING !! PCM Dependent Tests May Fail ***
*** WARNING !! Board Is Not Able To Boot ***

means no clock is provided in the shelf.

[mejust]

Yes You are Right

Thank You