One Way Speech Issue

Post Reply
royce.clark
Member
Posts: 11
Joined: 08 Sep 2008 19:13

One Way Speech Issue

Post by royce.clark » 20 Mar 2014 15:56

I have an issue with one way speech using the MyIC sip companion mobile client.

I have just upgraded an existing OXO customer to RCE release 9.1 and installed 7 MyIC mobile client licences with 7 SIP companion licences.

The installation of the software is fine and the mobile side of the MyIC client works fine. The client will register as SIP companion and I am able to make and receive calls ok on the internal network. However I am always getting one way speech when talking to an existing desk phone or making an outside call. I can get voice to the PABX but I am not receiving anything back to the MyIC Client.

Funny enough it works fine between 2 MyIC SIP Clients within the network (even on different Wifi terminals)

The PABX is on a different IP address to the internal network and we are using a firewall router to join the networks (Routing not NAT)

All SIP registration messages and call setup messages work fine (so that proves routing is OK)
I have run a trace at the PABX port and I get both speech paths in and out. (PABX is OK)
I have run a trace outside the firewall on the internal network side and I get both speech paths. (Firewall router is not the issue)
I have also tried using a different Wifi access point and I get the same issue. I can register other SIP clients on the same network without issue. (WiFi access point is not the issue)

Given that it works fine between 2 MyIC SIP companions proves my configuration is correct

The trace shows that the are using the same g711 codec

The trace shows clear communication between the PABX and the MyIC device

If anyone has any ideas where to go to from here it would be much appreciated. I have been wrecking my brain over this for months :(

User avatar
cavagnaro
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 7001
Joined: 14 Sep 2005 19:45
Location: Brasil, Porto Alegre
Contact:

Re: One Way Speech Issue

Post by cavagnaro » 20 Mar 2014 19:29

Routing not NAT... What do you mean? The fact that PBX original IP address is masked or changed is NAT and SIP is not friendly with it. You will need to use an SBC.
Ignorance is not the problem, the problem is the one who doesn't want to learn

OTUC/ICS ACFE/ACSE R3.0/4.0/5.0/6.0
Certified Genesys CIV 8.5
Certified Genesys Troubleshooting 8.5
Certified Genesys BEP 8.x
Genesys Developer

User avatar
cavagnaro
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 7001
Joined: 14 Sep 2005 19:45
Location: Brasil, Porto Alegre
Contact:

Re: One Way Speech Issue

Post by cavagnaro » 20 Mar 2014 19:33

And the fact that it works between 2 myIC means that they are only doing direct RTP between them.
Ignorance is not the problem, the problem is the one who doesn't want to learn

OTUC/ICS ACFE/ACSE R3.0/4.0/5.0/6.0
Certified Genesys CIV 8.5
Certified Genesys Troubleshooting 8.5
Certified Genesys BEP 8.x
Genesys Developer

royce.clark
Member
Posts: 11
Joined: 08 Sep 2008 19:13

Re: One Way Speech Issue

Post by royce.clark » 26 Mar 2014 16:53

Thank you. You are 100% correct.

I installed a Wifi router on the same network as the PABX with no issue. Looks like a need to redesign the network.

User avatar
tot3nkopf
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 4023
Joined: 02 Feb 2006 10:41
Location: Germany & Romania
Contact:

Re: One Way Speech Issue

Post by tot3nkopf » 27 Mar 2014 04:19

royce.clark wrote:Thank you. You are 100% correct.

I installed a Wifi router on the same network as the PABX with no issue. Looks like a need to redesign the network.
Or use SIP ALG aware router.

User avatar
murraya
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 900
Joined: 16 Oct 2007 02:35

Re: One Way Speech Issue

Post by murraya » 27 Mar 2014 05:11

I thought you learned better than that from me royce :?
Best Regards
Murray

ACSE 10.0 corporate
ACSE 6.x IPT data

royce.clark
Member
Posts: 11
Joined: 08 Sep 2008 19:13

Re: One Way Speech Issue

Post by royce.clark » 19 May 2014 21:35

True Murray.

I knew this was the case for IP phones but thought it would be OK for SIP.

I have got it working now that the firewall is routing not NATing.

I still have one issue. The app is intermittently not ringing, I can still answer the call but no sound. Any ideas???

User avatar
cavagnaro
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 7001
Joined: 14 Sep 2005 19:45
Location: Brasil, Porto Alegre
Contact:

Re: One Way Speech Issue

Post by cavagnaro » 20 May 2014 10:06

lol you have the answer...no magic tricks on ICS, just check your network
Ignorance is not the problem, the problem is the one who doesn't want to learn

OTUC/ICS ACFE/ACSE R3.0/4.0/5.0/6.0
Certified Genesys CIV 8.5
Certified Genesys Troubleshooting 8.5
Certified Genesys BEP 8.x
Genesys Developer

User avatar
murraya
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
Posts: 900
Joined: 16 Oct 2007 02:35

Re: One Way Speech Issue

Post by murraya » 27 May 2014 04:24

turn up your hearing aid?
Best Regards
Murray

ACSE 10.0 corporate
ACSE 6.x IPT data

Post Reply

Return to “MyIC (My Instant Communicator)”