H323 Trunking Alcatel OXE to Avaya IP Office
-
- Member
- Posts: 64
- Joined: 16 May 2013 02:23
H323 Trunking Alcatel OXE to Avaya IP Office
Hi everyone,
i am configuring H323 trunking between Alcatel OXE(common HW) to Avaya IP office.
1.Created TG with ISDN All countries, T2 specification as "IP"
2.Mapped to the GD3 card in TG third lvl.
3.created a prefix as professional TG siezer.
4.configured the avaya PBX number in direact speed dialing. Inside the call number is prefix+the avaya Pbx number and mentioned the avaya PBX IP also.
But i am getting below error. when i dial avaya PBX number.
(1)nic_pbx>
(1)nic_pbx> t3
--> Cleaning mtracer...
--> Positionning t3 filters...
+--------+-------+--------+--------+---------+---------+----------+------+
| filter | desti | src_id | cr_nbr | cpl_nbr | us_term | term_nbr | type |
+--------+-------+--------+--------+---------+---------+----------+------+
| 0 | ** | ** | * | ** | * | *** | 165 |
| 1 | ** | ** | * | ** | * | *** | 166 |
| 2 | ** | ** | * | ** | * | *** | 167 |
| 3 | | | | | | | |
| 4 | | | | | | | |
| 5 | | | | | | | |
| 6 | | | | | | | |
| 7 | | | | | | | |
+--------+-------+--------+--------+---------+---------+----------+------+
Traces Analyser activated
mtracer started ...
(090849:000001) MTRACER host (192.168.15.1, nic_pbx), version: R9.1-i1.605-25-b-
ke-c82
(090849:000001) MTRACER num: 013, time: 2016/03/10 13:31:06, loss: 0%
______________________________________________________________________________
| (090872:000002) 1299: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 70 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 45
|______________________________________________________________________________
|
| [9f] Non-locking shift. codeset : 7
| [a2] EI_IP_TYPE_TERM
| [9f] Non-locking shift. codeset : 7
| IE:[05] EI_IP_INFOS (l=9) -> G723 Ece 1 Vad 0 Profil 2, IPv4 :10.13.16.30.
| [9f] Non-locking shift. codeset : 7
| IE:[06] EI_IP_PAYLOADS (l=1) -> G729 Ece 1 Vad 0
| [9f] Non-locking shift. codeset : 7
| IE:[07] EI_IP_QOS (l=3) b8 a0 00
| [9f] Non-locking shift. codeset : 7
| IE:[0a] EI_RTP_INFO (l=2)
| -> stop_packet=0 stop_rtp=0 h323=0 wc=0 rf=0 udp=1 rqm=0
| -> Transm_Bande=1 detection_Q23=1 dtmf_payload=96
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[6c] CALLING_NUMBER (l=5) -> 01 81 Num : 253
| IE:[70] CALLED_NUMBER (l=4) -> 81 Num : 138
| IE:[7d] HLC (l=2) 91 81
| [a1] Sending complete
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000004) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 45
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=2) a9 83 -> T2 : B channel
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000005) 1299: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 26 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : STATUS [7d] Call ref : 00 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=3) 81 e4 18 -> [e4] INVALID INFORMATION ELEMENT CONTENTS
| IE:[14] CALL_STATE (l=1) 01
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000006) Concatenated-Physical-Event :
| long: 24 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : DISCONNECT [45] Call ref : 80 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=4) 01 80 e5 7d -> [e5] MESSAGE NOT COMPATIBLE WITH CALL STATE
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000007) 1299: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : RELEASE [4d] Call ref : 00 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 90 -> [90] NORMAL CALL CLEARING
|______________________________________________________________________________
______________________________________________________________________________
| (090874:000008) Concatenated-Physical-Event :
| long: 23 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : REL COMP [5a] Call ref : 80 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=3) 01 80 80 -> [80] UNKNOWN
|______________________________________________________________________________
(1)nic_pbx>
I ignored the ISDN msg setting in mgr/system also. But still not working.
Anyone give some suggestion to help me to close the issue.
Regards,
Rajan K.S
i am configuring H323 trunking between Alcatel OXE(common HW) to Avaya IP office.
1.Created TG with ISDN All countries, T2 specification as "IP"
2.Mapped to the GD3 card in TG third lvl.
3.created a prefix as professional TG siezer.
4.configured the avaya PBX number in direact speed dialing. Inside the call number is prefix+the avaya Pbx number and mentioned the avaya PBX IP also.
But i am getting below error. when i dial avaya PBX number.
(1)nic_pbx>
(1)nic_pbx> t3
--> Cleaning mtracer...
--> Positionning t3 filters...
+--------+-------+--------+--------+---------+---------+----------+------+
| filter | desti | src_id | cr_nbr | cpl_nbr | us_term | term_nbr | type |
+--------+-------+--------+--------+---------+---------+----------+------+
| 0 | ** | ** | * | ** | * | *** | 165 |
| 1 | ** | ** | * | ** | * | *** | 166 |
| 2 | ** | ** | * | ** | * | *** | 167 |
| 3 | | | | | | | |
| 4 | | | | | | | |
| 5 | | | | | | | |
| 6 | | | | | | | |
| 7 | | | | | | | |
+--------+-------+--------+--------+---------+---------+----------+------+
Traces Analyser activated
mtracer started ...
(090849:000001) MTRACER host (192.168.15.1, nic_pbx), version: R9.1-i1.605-25-b-
ke-c82
(090849:000001) MTRACER num: 013, time: 2016/03/10 13:31:06, loss: 0%
______________________________________________________________________________
| (090872:000002) 1299: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 70 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 45
|______________________________________________________________________________
|
| [9f] Non-locking shift. codeset : 7
| [a2] EI_IP_TYPE_TERM
| [9f] Non-locking shift. codeset : 7
| IE:[05] EI_IP_INFOS (l=9) -> G723 Ece 1 Vad 0 Profil 2, IPv4 :10.13.16.30.
| [9f] Non-locking shift. codeset : 7
| IE:[06] EI_IP_PAYLOADS (l=1) -> G729 Ece 1 Vad 0
| [9f] Non-locking shift. codeset : 7
| IE:[07] EI_IP_QOS (l=3) b8 a0 00
| [9f] Non-locking shift. codeset : 7
| IE:[0a] EI_RTP_INFO (l=2)
| -> stop_packet=0 stop_rtp=0 h323=0 wc=0 rf=0 udp=1 rqm=0
| -> Transm_Bande=1 detection_Q23=1 dtmf_payload=96
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[6c] CALLING_NUMBER (l=5) -> 01 81 Num : 253
| IE:[70] CALLED_NUMBER (l=4) -> 81 Num : 138
| IE:[7d] HLC (l=2) 91 81
| [a1] Sending complete
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000004) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 45
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=2) a9 83 -> T2 : B channel
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000005) 1299: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 26 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : STATUS [7d] Call ref : 00 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=3) 81 e4 18 -> [e4] INVALID INFORMATION ELEMENT CONTENTS
| IE:[14] CALL_STATE (l=1) 01
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000006) Concatenated-Physical-Event :
| long: 24 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : DISCONNECT [45] Call ref : 80 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=4) 01 80 e5 7d -> [e5] MESSAGE NOT COMPATIBLE WITH CALL STATE
|______________________________________________________________________________
______________________________________________________________________________
| (090873:000007) 1299: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : RELEASE [4d] Call ref : 00 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 90 -> [90] NORMAL CALL CLEARING
|______________________________________________________________________________
______________________________________________________________________________
| (090874:000008) Concatenated-Physical-Event :
| long: 23 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : REL COMP [5a] Call ref : 80 45
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=3) 01 80 80 -> [80] UNKNOWN
|______________________________________________________________________________
(1)nic_pbx>
I ignored the ISDN msg setting in mgr/system also. But still not working.
Anyone give some suggestion to help me to close the issue.
Regards,
Rajan K.S
Re: H323 Trunking Alcatel OXE to Avaya IP Office
Hello,
On the IP trunk, is B Channel Choice set to True?
Regards
On the IP trunk, is B Channel Choice set to True?
Regards
-
- Member
- Posts: 64
- Joined: 16 May 2013 02:23
Re: H323 Trunking Alcatel OXE to Avaya IP Office
Hi sadim,
Thanks for the replay.
currently i configured "B" channel choice is "false". if i set B channel "True", getting Busy tone and in Trace showing "no B channel".
Regards,
Rajan K.S
Thanks for the replay.
currently i configured "B" channel choice is "false". if i set B channel "True", getting Busy tone and in Trace showing "no B channel".
Regards,
Rajan K.S
Re: H323 Trunking Alcatel OXE to Avaya IP Office
B channel choice must be set to true on a h323 cnx
Attach a trace with this configuration
Enviado do meu ALE-L21 através de Tapatalk
Attach a trace with this configuration
Enviado do meu ALE-L21 através de Tapatalk
Re: H323 Trunking Alcatel OXE to Avaya IP Office
Strange message from Avaya B channel but without indication witch B channel.
_____________________________________________________________________________
| (090873:000004) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 45
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=2) a9 83 -> T2 : B channel
|______________________________________________________________________________
_____________________________________________________________________________
| (090873:000004) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 45
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=2) a9 83 -> T2 : B channel
|______________________________________________________________________________
Re: H323 Trunking Alcatel OXE to Avaya IP Office
Hello Vad,
My best guess is that this is due the missing of the channel (IE:[18] CHANNEL (l=3) a8 83 81 -> T2 : No B channel) in the setup msg that was sent by OXE.
Also, RTP and RTPC ports are missing on Setup, but once again, i believe that is due the fact that he has B Channel Choice at False,
He must provide a new trace with B Channel Choice at True.
Best Regards
My best guess is that this is due the missing of the channel (IE:[18] CHANNEL (l=3) a8 83 81 -> T2 : No B channel) in the setup msg that was sent by OXE.
Also, RTP and RTPC ports are missing on Setup, but once again, i believe that is due the fact that he has B Channel Choice at False,
He must provide a new trace with B Channel Choice at True.
Best Regards
-
- Member
- Posts: 64
- Joined: 16 May 2013 02:23
Re: H323 Trunking Alcatel OXE to Avaya IP Office
Hello saidm & vlad,
Please fidn the below traces, when i configure "B channel Choice is True".
(1)nic_pbx> t3
--> Cleaning mtracer...
--> Positionning t3 filters...
+--------+-------+--------+--------+---------+---------+----------+------+
| filter | desti | src_id | cr_nbr | cpl_nbr | us_term | term_nbr | type |
+--------+-------+--------+--------+---------+---------+----------+------+
| 0 | ** | ** | * | ** | * | *** | 165 |
| 1 | ** | ** | * | ** | * | *** | 166 |
| 2 | ** | ** | * | ** | * | *** | 167 |
| 3 | | | | | | | |
| 4 | | | | | | | |
| 5 | | | | | | | |
| 6 | | | | | | | |
| 7 | | | | | | | |
+--------+-------+--------+--------+---------+---------+----------+------+
Traces Analyser activated
mtracer started ...
(369489:000001) MTRACER host (192.168.15.1, nic_pbx), version: R9.1-i1.605-25-b-
ke-c82
(369489:000001) MTRACER num: 017, time: 2016/03/15 12:22:19, loss: 0%
______________________________________________________________________________
| (369516:000002) 1298: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 103 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 61
|______________________________________________________________________________
|
| [9f] Non-locking shift. codeset : 7
| [a2] EI_IP_TYPE_TERM
| [9f] Non-locking shift. codeset : 7
| IE:[05] EI_IP_INFOS (l=9) -> G723 Ece 1 Vad 0 Profil 2, IPv4 :10.13.16.30.
| [9f] Non-locking shift. codeset : 7
| IE:[06] EI_IP_PAYLOADS (l=1) -> G729 Ece 1 Vad 0
| [9f] Non-locking shift. codeset : 7
| IE:[07] EI_IP_QOS (l=3) b8 a0 00
| [9f] Non-locking shift. codeset : 7
| IE:[0a] EI_RTP_INFO (l=30)
| -> stop_packet=0 stop_rtp=0 h323=0 wc=0 rf=0 udp=1 rqm=0
| -> Transm_Bande=1 detection_Q23=1 dtmf_payload=96
| -> Port RTP = 32514, IPv4 : 192. 168. 1. 221.
| -> Port RTCP SR = 32515, IPv4 : 192. 168. 1. 221.
| -> Port RTCP RR = 32515, IPv4 : 192. 168. 1. 221.
| -> Port Fax = 0, IPv4 : 0. 0. 0. 0.
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[18] CHANNEL (l=3) a8 83 81 -> T2 : No B channel
| IE:[6c] CALLING_NUMBER (l=5) -> 01 81 Num : 253
| IE:[70] CALLED_NUMBER (l=4) -> 81 Num : 138
| IE:[7d] HLC (l=2) 91 81
| [a1] Sending complete
|______________________________________________________________________________
______________________________________________________________________________
| (369517:000004) Concatenated-Physical-Event :
| long: 21 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 61
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=1) a8 -> T2 : No B channel
|______________________________________________________________________________
______________________________________________________________________________
| (369576:000005) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : RELEASE [4d] Call ref : 80 61
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 83 -> [83] NO ROUTE TO DESTINATION
|______________________________________________________________________________
______________________________________________________________________________
| (369576:000006) 1298: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : REL COMP [5a] Call ref : 00 61
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 90 -> [90] NORMAL CALL CLEARING
|______________________________________________________________________________
I am getting busy tone, when i dial the Avaya PBX extension number.
Sorry ..had little delay on uploading this trace..
please share your suggestions ...
Thanks & Regards,
Rajan K.S
Please fidn the below traces, when i configure "B channel Choice is True".
(1)nic_pbx> t3
--> Cleaning mtracer...
--> Positionning t3 filters...
+--------+-------+--------+--------+---------+---------+----------+------+
| filter | desti | src_id | cr_nbr | cpl_nbr | us_term | term_nbr | type |
+--------+-------+--------+--------+---------+---------+----------+------+
| 0 | ** | ** | * | ** | * | *** | 165 |
| 1 | ** | ** | * | ** | * | *** | 166 |
| 2 | ** | ** | * | ** | * | *** | 167 |
| 3 | | | | | | | |
| 4 | | | | | | | |
| 5 | | | | | | | |
| 6 | | | | | | | |
| 7 | | | | | | | |
+--------+-------+--------+--------+---------+---------+----------+------+
Traces Analyser activated
mtracer started ...
(369489:000001) MTRACER host (192.168.15.1, nic_pbx), version: R9.1-i1.605-25-b-
ke-c82
(369489:000001) MTRACER num: 017, time: 2016/03/15 12:22:19, loss: 0%
______________________________________________________________________________
| (369516:000002) 1298: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 103 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 61
|______________________________________________________________________________
|
| [9f] Non-locking shift. codeset : 7
| [a2] EI_IP_TYPE_TERM
| [9f] Non-locking shift. codeset : 7
| IE:[05] EI_IP_INFOS (l=9) -> G723 Ece 1 Vad 0 Profil 2, IPv4 :10.13.16.30.
| [9f] Non-locking shift. codeset : 7
| IE:[06] EI_IP_PAYLOADS (l=1) -> G729 Ece 1 Vad 0
| [9f] Non-locking shift. codeset : 7
| IE:[07] EI_IP_QOS (l=3) b8 a0 00
| [9f] Non-locking shift. codeset : 7
| IE:[0a] EI_RTP_INFO (l=30)
| -> stop_packet=0 stop_rtp=0 h323=0 wc=0 rf=0 udp=1 rqm=0
| -> Transm_Bande=1 detection_Q23=1 dtmf_payload=96
| -> Port RTP = 32514, IPv4 : 192. 168. 1. 221.
| -> Port RTCP SR = 32515, IPv4 : 192. 168. 1. 221.
| -> Port RTCP RR = 32515, IPv4 : 192. 168. 1. 221.
| -> Port Fax = 0, IPv4 : 0. 0. 0. 0.
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[18] CHANNEL (l=3) a8 83 81 -> T2 : No B channel
| IE:[6c] CALLING_NUMBER (l=5) -> 01 81 Num : 253
| IE:[70] CALLED_NUMBER (l=4) -> 81 Num : 138
| IE:[7d] HLC (l=2) 91 81
| [a1] Sending complete
|______________________________________________________________________________
______________________________________________________________________________
| (369517:000004) Concatenated-Physical-Event :
| long: 21 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 61
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=1) a8 -> T2 : No B channel
|______________________________________________________________________________
______________________________________________________________________________
| (369576:000005) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : RELEASE [4d] Call ref : 80 61
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 83 -> [83] NO ROUTE TO DESTINATION
|______________________________________________________________________________
______________________________________________________________________________
| (369576:000006) 1298: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : REL COMP [5a] Call ref : 00 61
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 90 -> [90] NORMAL CALL CLEARING
|______________________________________________________________________________
I am getting busy tone, when i dial the Avaya PBX extension number.
Sorry ..had little delay on uploading this trace..
please share your suggestions ...
Thanks & Regards,
Rajan K.S
Re: H323 Trunking Alcatel OXE to Avaya IP Office
Hello,
Time to check in Avaya system, the reason of No Route to Destination.
138 is a Avaya internal Set, G729/G723 are ok for Avaya ?
Regards
Time to check in Avaya system, the reason of No Route to Destination.
138 is a Avaya internal Set, G729/G723 are ok for Avaya ?
Regards
-
- Member
- Posts: 64
- Joined: 16 May 2013 02:23
Re: H323 Trunking Alcatel OXE to Avaya IP Office
hi,
Sorry for the delay replay. Avaya guy is saying that he added all the codecs available in the system.
And in our trace, its showing that "no B channel" is that normal...?
Thanks
Sorry for the delay replay. Avaya guy is saying that he added all the codecs available in the system.
And in our trace, its showing that "no B channel" is that normal...?
Thanks
- cavagnaro
- Alcatel Unleashed Certified Guru
- Posts: 7014
- Joined: 14 Sep 2005 19:45
- Location: Brasil, Porto Alegre
- Contact:
Re: H323 Trunking Alcatel OXE to Avaya IP Office
138 is a Avaya internal Set? As sadim asks, seems maybe to be a remote set over other network. Ask Avaya guys for their logs.
Ignorance is not the problem, the problem is the one who doesn't want to learn
OTUC/ICS ACFE/ACSE R3.0/4.0/5.0/6.0
Certified Genesys CIV 8.5
Certified Genesys Troubleshooting 8.5
Certified Genesys BEP 8.x
Genesys Developer
OTUC/ICS ACFE/ACSE R3.0/4.0/5.0/6.0
Certified Genesys CIV 8.5
Certified Genesys Troubleshooting 8.5
Certified Genesys BEP 8.x
Genesys Developer