Post
by rajansuruli15 » 15 Mar 2016 05:05
Hello saidm & vlad,
Please fidn the below traces, when i configure "B channel Choice is True".
(1)nic_pbx> t3
--> Cleaning mtracer...
--> Positionning t3 filters...
+--------+-------+--------+--------+---------+---------+----------+------+
| filter | desti | src_id | cr_nbr | cpl_nbr | us_term | term_nbr | type |
+--------+-------+--------+--------+---------+---------+----------+------+
| 0 | ** | ** | * | ** | * | *** | 165 |
| 1 | ** | ** | * | ** | * | *** | 166 |
| 2 | ** | ** | * | ** | * | *** | 167 |
| 3 | | | | | | | |
| 4 | | | | | | | |
| 5 | | | | | | | |
| 6 | | | | | | | |
| 7 | | | | | | | |
+--------+-------+--------+--------+---------+---------+----------+------+
Traces Analyser activated
mtracer started ...
(369489:000001) MTRACER host (192.168.15.1, nic_pbx), version: R9.1-i1.605-25-b-
ke-c82
(369489:000001) MTRACER num: 017, time: 2016/03/15 12:22:19, loss: 0%
______________________________________________________________________________
| (369516:000002) 1298: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 103 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 61
|______________________________________________________________________________
|
| [9f] Non-locking shift. codeset : 7
| [a2] EI_IP_TYPE_TERM
| [9f] Non-locking shift. codeset : 7
| IE:[05] EI_IP_INFOS (l=9) -> G723 Ece 1 Vad 0 Profil 2, IPv4 :10.13.16.30.
| [9f] Non-locking shift. codeset : 7
| IE:[06] EI_IP_PAYLOADS (l=1) -> G729 Ece 1 Vad 0
| [9f] Non-locking shift. codeset : 7
| IE:[07] EI_IP_QOS (l=3) b8 a0 00
| [9f] Non-locking shift. codeset : 7
| IE:[0a] EI_RTP_INFO (l=30)
| -> stop_packet=0 stop_rtp=0 h323=0 wc=0 rf=0 udp=1 rqm=0
| -> Transm_Bande=1 detection_Q23=1 dtmf_payload=96
| -> Port RTP = 32514, IPv4 : 192. 168. 1. 221.
| -> Port RTCP SR = 32515, IPv4 : 192. 168. 1. 221.
| -> Port RTCP RR = 32515, IPv4 : 192. 168. 1. 221.
| -> Port Fax = 0, IPv4 : 0. 0. 0. 0.
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[18] CHANNEL (l=3) a8 83 81 -> T2 : No B channel
| IE:[6c] CALLING_NUMBER (l=5) -> 01 81 Num : 253
| IE:[70] CALLED_NUMBER (l=4) -> 81 Num : 138
| IE:[7d] HLC (l=2) 91 81
| [a1] Sending complete
|______________________________________________________________________________
______________________________________________________________________________
| (369517:000004) Concatenated-Physical-Event :
| long: 21 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 61
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=1) a8 -> T2 : No B channel
|______________________________________________________________________________
______________________________________________________________________________
| (369576:000005) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 2 cpl: 0 us: 0 term: 0 type a5
| tei: 0 >>>> message received : RELEASE [4d] Call ref : 80 61
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 83 -> [83] NO ROUTE TO DESTINATION
|______________________________________________________________________________
______________________________________________________________________________
| (369576:000006) 1298: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 2 cpl: 0 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : REL COMP [5a] Call ref : 00 61
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 90 -> [90] NORMAL CALL CLEARING
|______________________________________________________________________________
I am getting busy tone, when i dial the Avaya PBX extension number.
Sorry ..had little delay on uploading this trace..
please share your suggestions ...
Thanks & Regards,
Rajan K.S