OS 6850 file system?

[yanxiaomin]

Did anyone who know the omniswitch flash file system ?it it Fat32?fat? ntfs? or ext2?or other ?who can tell me how I can format the flash in vxwork mode or in miniboot mode?

[yanxiaomin]

May I use the "erase" to format the flash ?

=> ?
? - alias for 'help'
autoscr - run script from memory
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cmp - memory compare
coninfo - print console devices and informations
cp - memory copy
crc32 - checksum calculation
diskboot- boot from IDE device
echo - echo args to console
erase - erase FLASH memory
fatdelete - delete a file from a fat filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fatwrite - write binary file to a fat filesystem
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print online help
icrc32 - checksum calculation
ide - IDE sub-system
iloop - infinite loop on address range
imd - i2c memory display
iminfo - print header information for application image
imls - list all images found in flash
imm - i2c memory modify (auto-incrementing)
imw - memory write (fill)
inm - memory modify (constant address)
iprobe - probe to discover valid I2C chip addresses
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loop - infinite loop on address range
md - memory display
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuraton Space
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sleep - delay execution for some time
tftpboot- boot image via network using TFTP protocol
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
=>

[cedric1]

hello

In miniboot mode

type ioHelp

you have command to format flash and file system.

Regards

Cedric

[yanxiaomin]

Thanks. after I format the flash and upload the image files the 6850 run normal .but it when NI up it output in consle.
I use 126W power.

logs :

THU JUL 23 14:47:33 : LANPOWER (108) info message:
+++ lpGetMaxPorts: invalid NI Type 42012214 Slot 1 ERROR!!

[cedric1]

hi

did you try to launch command lanpower start 1

did you get an error ?

Did you have power feeding or not ? connect Wifi AP or a phone to check

Cedric

[benny]

The 126W AC power-supply doesn't support PoE. You need the 360W or 510W variant.

P.S. Kindly stop to post your question several times. Thanks.

-benny

[cedric1]

hi yanxiaomin

Why did you use a P24 switch with a 126W.

Normally when you order a POE switch you can only choose between 360 or 510 Watts.

cedric

[yanxiaomin]

thanks .there was something wrong with my 360W power,and I sended it to alcatel. when I poweroff the switch's lanpower it was normal now!

[lmherdvera]

Please Help..how can I delete the missed type configuration..
Thank you in very much...

=> printenv
bootargs=
bootcmd=run miniboot
bootdelay=1
loads_echo=1
ipaddr=192.168.10.1
serverip=
rootpath=
gatewayip=
netmask=255.255.255.0
hostname=OS68xx
bootfile=
loadaddr=0x1000000
serialmode=modemControlOff
----------------------------------> bootfalgs=0x1000
----------------------------------->booflags=0x0
----------------------------------->baurate=115200
bootflags=0x1000
baudrate=115200
stdin=serial
stdout=serial
stderr=serial
miniboot=bootm 0xff900000
osboot=run miniboot
ramsize=0x20000000

Environment size: 385/8188 bytes

[silvio]

this wrong entries should do not issue in your switch. But you can try to reset all.
Try "purge" or "purgeenv" - I'm not sure if this command will be supported at 6850.
But you can also delete the file bootparams and restart the switch.
Than the default settings will be used.
regards
Silvio