Hi All,
OXE R10, Common HW
I need to setup a analog fax with an Audiocodec MP-112.
Have done it serval time before without problems. This time it seem like the menus in the software have changed? I have done the configuration up untill where I need to set the "Endpoint Numbers". Until now this have been done in "‘Endpoint Phone Number Table’ page (Configuration tab > Protocol Configuration > Endpoint Number > Endpoint Phone Number)"
That menu is gone! So, does anyone know where to find/configure in the new software version?
Software version on the Box is:
Version ID: 6.60A.241.010
Best Regards
Audiocodec MP-112. New menu/software
- tot3nkopf
- Alcatel Unleashed Certified Guru
- Posts: 4058
- Joined: 02 Feb 2006 10:41
- Location: Germany & Romania
- Contact:
Re: Audiocodec MP-112. New menu/software
If it is not covered by ALU in the latest IWR, I think you should raise that to Audiocodes support.
-
- Member
- Posts: 3
- Joined: 31 Jan 2014 09:45
Re: Audiocodec MP-112. New menu/software
I have the same problem, new menu software, have anyone got answer from Audiocodes support ?
- tot3nkopf
- Alcatel Unleashed Certified Guru
- Posts: 4058
- Joined: 02 Feb 2006 10:41
- Location: Germany & Romania
- Contact:
Re: Audiocodec MP-112. New menu/software
Or maybe you can load the old firmware and use the instructions that you have...Audiocodes firmware and instructions on how to flash it is easy to procure..terjeornes wrote:I have the same problem, new menu software, have anyone got answer from Audiocodes support ?
Re: Audiocodec MP-112. New menu/software
I had a talk with AudioCodec support and they sent me a working config file. I corrected it for my specific site and it worked!
Just be aware: I tested it only with an analog phone NOT WITH A REAL FAX. (Incomming/outgoing) Simply becuase the customer suddenly found out they did not want to use fax anymore!! But I expect it to work
Remember to change the IP adresses + user numbers (use notepad find/replace)
Best Regards
PS: let med know if it works so I can use it for other sites with fax
Just be aware: I tested it only with an analog phone NOT WITH A REAL FAX. (Incomming/outgoing) Simply becuase the customer suddenly found out they did not want to use fax anymore!! But I expect it to work
Remember to change the IP adresses + user numbers (use notepad find/replace)
Best Regards
PS: let med know if it works so I can use it for other sites with fax
You do not have the required permissions to view the files attached to this post.
-
- Member
- Posts: 3
- Joined: 31 Jan 2014 09:45
Re: Audiocodec MP-112. New menu/software
This did not work, but the problem may be in the OXO, is it possible to hire some help to set this up ?
(I have set up an Konftel 300IP, and had to change VoIP Parameter from H323 to SIP.)
(I have set up an Konftel 300IP, and had to change VoIP Parameter from H323 to SIP.)
Re: Audiocodec MP-112. New menu/software
I did this on OXE. Afraid I can not help with OXO. Tho my advice is that you start testing ur global SIP setup with a SIP software phone. Ex. with a X-lite SIP phone.
Re: Audiocodec MP-112. New menu/software
[Voice Engine Params]
CallProgressTonesFilename = 'usa_tones_13.dat'
FaxTransportMode = 0
V22ModemTransportType = 0
V23ModemTransportType = 0
V32ModemTransportType = 0
V34ModemTransportType = 0
TTYTRANSPORTTYPE = 1
CallProgressTonesFilename = 'usa_tones_13.dat'
FaxTransportMode = 0
V22ModemTransportType = 0
V23ModemTransportType = 0
V32ModemTransportType = 0
V34ModemTransportType = 0
TTYTRANSPORTTYPE = 1
-
- Member
- Posts: 3
- Joined: 31 Jan 2014 09:45
Re: Audiocodec MP-112. New menu/software
It is working, after some studying of other SIP communication i got it to work, the Audiocode it is connected to a modem and not fax, but i guess that should be the same.
Thanks to FN_DK.
Thanks to FN_DK.