Problem in 4059IP attendant configuration,
-
- Member
- Posts: 3
- Joined: 28 Jan 2015 16:12
Problem in 4059IP attendant configuration,
Hello Dear,
I am installing a new system and facing a problem in 4059EE. IP soft phone V11.0.15 is working fine. But when i install 4059EE(V 1.5.0.10). It installs successfully. But when i open it gives an error of (OmniPCX communication failure:SS_SBC_EXTENDED:L3OPEN, l2 protocol init failed).
There is no network is involved in between OXE. Two LAN cables are coming in a simple unmanaged LAN switch,One cable is from INT-IP3 card. and one cable is in that system on which 4059EE is installed.
Attached are the snapgshots. Please help
I am installing a new system and facing a problem in 4059EE. IP soft phone V11.0.15 is working fine. But when i install 4059EE(V 1.5.0.10). It installs successfully. But when i open it gives an error of (OmniPCX communication failure:SS_SBC_EXTENDED:L3OPEN, l2 protocol init failed).
There is no network is involved in between OXE. Two LAN cables are coming in a simple unmanaged LAN switch,One cable is from INT-IP3 card. and one cable is in that system on which 4059EE is installed.
Attached are the snapgshots. Please help
You do not have the required permissions to view the files attached to this post.
Re: Problem in 4059IP attendant configuration,
what is the setting on the console set-up page can you show us a picture of that?
"Be aware ask a stupid question without at least trying to find the answer first you may get a stupid answer....."
Re: Problem in 4059IP attendant configuration,
hi,,, im getting the same issue. tried with 1.5 and 1.6 but still the same. i knw i have installed 3 sets before. but this time no matter what i do it pops up the same massage as you do. any idea what we can do?
Re: Problem in 4059IP attendant configuration,
Hello qasim
I have the same fault using windows 7 with 4059EE version 1.5 and 1.6. Any solution?
I have the same fault using windows 7 with 4059EE version 1.5 and 1.6. Any solution?
-
- Member
- Posts: 1
- Joined: 17 Nov 2009 05:19
Re: Problem in 4059IP attendant configuration,
I am installing a new system and facing a problem in 4059EE. IP soft phone V11.0.15 is working fine. But when i install 4059EE(V 1.5.0.10). It installs successfully. But when i open it gives an error of (OmniPCX communication failure:SS_SBC_EXTENDED:L3OPEN, l2 protocol init failed).
There is no network is involved in between OXE. Two LAN cables are coming in a simple unmanaged LAN switch,
Please help
There is no network is involved in between OXE. Two LAN cables are coming in a simple unmanaged LAN switch,
Please help
Re: Problem in 4059IP attendant configuration,
disable the firewall and any antivirus been installed
Re: Problem in 4059IP attendant configuration,
hi
you must open tftp from windows features and to disable firewall.
you must open tftp from windows features and to disable firewall.
Re: Problem in 4059IP attendant configuration,
solved
In my case, entering regedit -> HKEY_LOCAL_MACHINE / SYSTEM / CurrentControlSet / services / Tcpip / Linkage
Verify that the BIND file with the MAC address of the network card as the first position, we can see in (Parameters / interfaces)
By doing this it has worked. I hope it helps you
In my case, entering regedit -> HKEY_LOCAL_MACHINE / SYSTEM / CurrentControlSet / services / Tcpip / Linkage
Verify that the BIND file with the MAC address of the network card as the first position, we can see in (Parameters / interfaces)
By doing this it has worked. I hope it helps you
You do not have the required permissions to view the files attached to this post.
Re: Problem in 4059IP attendant configuration,
yes i forgit, this is a issue as well if the pc have multiple lan ports.
Re: Problem in 4059IP attendant configuration,
I have same error with 4059EE 1.6.2.1
SS_SBC_EXTENDED:L#OPEN,l2 protocol init failed
Packet capture shows 4059EE attempting tftp to OXE, OXE responds with "Client request without requested ethernet address"
I've looked in the registry as mentioned above, and pasted the interface matching the current IP at the top of the Bind Value Data, but it doesn't seem to help.
Windows firewall off. TFTP installed in Windows features. Attempted via same L2 as well as routed subnets.
Any further explanation of how to adjust the Bind registry, or ensure the OXE is getting the Ethernet data it needs to respond with tftp would be appreciated!
SS_SBC_EXTENDED:L#OPEN,l2 protocol init failed
Packet capture shows 4059EE attempting tftp to OXE, OXE responds with "Client request without requested ethernet address"
I've looked in the registry as mentioned above, and pasted the interface matching the current IP at the top of the Bind Value Data, but it doesn't seem to help.
Windows firewall off. TFTP installed in Windows features. Attempted via same L2 as well as routed subnets.
Any further explanation of how to adjust the Bind registry, or ensure the OXE is getting the Ethernet data it needs to respond with tftp would be appreciated!
You do not have the required permissions to view the files attached to this post.