MIGRATION INTERFACES CONFIG
This table does not concern the administrator - Reserved to specialist only.
It concerns the parameters of analog links with the migration shelves (PABX 5200, 5400).
The values of the attributes are different depending on the countries.

Instance (reserved)
SSI Interface - 5200
SSI = Standard Subscriber Interface (basic Z board)

Loop Break Hookflash
Hook Flash
Message Waiting Ringing
Message Waiting LED
Mess.Waiting Duration
Loop Interrupt Time
Inter Digit Time
Max Calibrated Break Time
Min Calibrated Break
Min Hook Flash Time
Min Offhook Wait Time
Hook Flash Disconnect Time
No Hook Flash Disconn.Time
Wait Ground On Time
Wait Ground Off Time
Power Up SLIC Time
Power Deny SLIC Time
Power Down Line Time
Ground Alarm Time
Offhook Repeat Time
Max Lockout Time

TIF Interface - 5200
TIF = Trunk Interface

Interdigit Time
Loop Feeding Digit Break Time
Loop Feeding Digit Make Time

MFR Interface - 5200
MFR = Detection Multi FRequencies

Min Dialtone Duration

SLI Interface - 5200
SLI = Special Line Interface

Seizure Time
Release Time

Analogic sets - 5400

List of the parameters:

• Min. duration calibration loop (button)
• Min. duration loop break hookflash
  
  Only used for DTMF extensions
  
  
• Min. duration active phase
• Min. duration inactive phase
• Max. duration inactive phase
• Off hook validation time
• On hook validation time
• Min. duration interdigit decadic
• Earth button validation duration
  The adjustment of the timer is made by number of units of 10 ms.

Min.Dur.Calibr.Loop (Button)
Min.dur.loop break Hookflash
Min.dur.active phase
Min.dur.inactive phase
Max.dur.inactive phase
Off hook Validation time
On hook Validation time
Min.dur.interdigit decadic
Earth Button Valid Duration

NDDI - 5400

List of the parameters:

• Active validation ringing time
• Max ringing off time
  
  (incoming call. The caller has hung up without any answer)
  
  
• Active masking time
• Deactivation masking answer time
• Timed distant release time
• Deactivation masking seize time
• Valid dial tone type 1 time
• Dial tone type 2 max make time (international)
• Dial tone type 2 max break time (international)
• Validation interpulse time
• DC digit interdigit time
• Calibrated loop time
• Deactivation mask call loop time
• Max cost pulse time
• Dial ton.type2 min make time (international)
• Dial ton.type2 max make check (international)
• Dial ton.type2 min break time (international)
• Dial ton.typ2 max break check (international)
• Min cost pulse time
• Trunk break time
• Trunk make time
  Except other instruction, the adjustment is made by number of 10 ms units.

Active Valid.Ringing Time
Max Ringing Off Time
Active Masking Time
Disactiv.Masking Answer Time
Timed Distant Release Time
Disactiv.Masking Seize Time
Valid.Dial Tone Type1 Time
Dial Tone Type2 Max Make Time
Dial Ton.Typ2 Max Break Time
Validation Interpulse Time
DC Digit Interdigit Time
Calibrated Loop Time
Disactiv.Mask.Call Loop Time
Max Metering Pulse Time
Dial Ton.Type2 Min Make Time
Dial Ton.Type2 Max Make Check
Dial Ton.Type2 Min Break Time
Dial Ton.Typ2 Max Break Check
Min_Metering Pulse Time
Trunk Break Time
Trunk Make Time

DDI - 5400

List of the parameters:

• Min validation seize time
• Min validation releas.time
  The adjustment is made by number of units of 10 ms.

Min Validation Seize Time
Min Validatation Releas.Time

E&M Tie Line - 5400

List of the parameters:

• DC interdigit time (outgoing call)
• Answer pulse time
• Release singl.level reduc. time
• Set release time
• Calibrated loop time
• Validation seize time
• Validation proceed to send time
• Validation dial tone time
• Validation rotary interdigit time (incoming call)
• Validation answer time
• Validation release time
• Post answer time
• Lower limit make time
• Lower limit break time
• Upperlimit break time
• Lower limit answer puls.time
• Upper limit answer pulse time
• Tin break time
• Tin make time
• Tin Masking time
  The adjustment is made by number of units of 10 ms.

DC Interdigit Time
Answer Pulse Time
Releas.Singl.Level Reduc.Time
Poste Release Time
Calibrated Loop Time
Validation Seize Time
Valid.Proceed To Send Time
Valid.Dial tone Time
Valid.Deca Interdigit Time
Validation Answer Time
Validation Release Time
Post Answer Time
Lower Limit Make Time
Lower Limit Break Time
Upper Limit Break Time
Lower Limit Answer Puls.Time
Upper Limit Answer Puls.Time
Tin_Break Time
Tin Make Time
Tin Masking Time