i having OXE crystall system R7.1 path 36d.
i config as below capture but intip card not work:
+-------------------------------------------------------------------+
| Cr | cpl| cpl type | hw type | cpl state | coupler ID |
|----|----|------------|-----------|--------------|-----------------|
| 0 | 0 | RMA|---------- |ONLY OPS FILE | BAD PCMS CODE |
| 0 | 1 | PCM2|---------- |ONLY OPS FILE | BAD PCMS CODE |
| 0 | 2 | NPRAE|---------- | IN SERVICE | 3BA23254AAAD04 |
| 0 | 3 | NDDI2|---------- | IN SERVICE | 3BA23171AABD01 |
| 0 | 4 | eUA32|---------- |ONLY OPS FILE | BAD PCMS CODE |
| 0 | 5 | eUA32|---------- | IN SERVICE | 3BA23266AAAA04 |
| 0 | 6 | CPU6|---------- | IN SERVICE | BAD PCMS CODE |
| 0 | 7 | eUA32|---------- | IN SERVICE | 3BA23266AAAA04 |
| 0 | 8 | INTIPA| INT-IP | INIT 1 RUN | BAD PCMS CODE |
| 0 | 9 | GPA2|---------- | IN SERVICE | 3BA23241AAAC05 |
| 0 | 12 | PCM2|---------- |ONLY OPS FILE | BAD PCMS CODE |
| 0 | 13 | RMA|---------- |ONLY MAO FILE | NO PCMS CODE |
+-------------------------------------------------------------------+
(1)viscohn> ping 192.168.1.254
PING 192.168.1.254 (192.168.1.254): 56 octets data
64 octets from 192.168.1.254: icmp_seq=0 ttl=255 time=1.2 ms
64 octets from 192.168.1.254: icmp_seq=1 ttl=255 time=0.9 ms
--- 192.168.1.254 ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.9/1.0/1.2 ms
(1)viscohn> cplstat 0 8
Tue Jun 29 17:18:56 CEST 2010
Logic coupler type : INTIPA (70);
MAO coupler type : INTIPA ;
Coupler state : INITIALIZATION 1 RUNNING ;
Protocol country : VIET_NAM (79);
Ghost equipment number : 30158 ;
First terminal number : 0 ;
Last terminal number : 1 ;
Specific data of the INT boards
Opposite crystal : 255
Opposite coupler : 255
Role part : 3
State of the link : 0
Signalling transmission mode : 0
Used TS : 0
Specific data of the IP boards
Board IP address (IPv4) : 192.168.1.254
Netmask IP : 255.255.255.0
Default Gateway IP address : 192.168.1.100
Board Ethernet Address : 00:80:9f:81:f4:a0
IP quality of service : 0
Current base UDP port : 0
Base UDP port for next initialization : 32000
Compression available for Gateway : 2
lqReview/Modify: Ethernet Parametersqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk
x x
x Node Number (reserved) : 1 x
x Shelf Address : 0 x
x Board Address : 8 x
x Shelf - Board Address : 0-8 x
x x
x Interface Type + INTIPA x
x Board IP Address : 192.168.1.254 x
x IP NetMask : 255.255.255.0 x
x Default Gateway IP Address : 192.168.1.100 x
x IP Quality of service : 0 x
x Cryptographic box address : ----------------------------------------------- x
x Board Ethernet Address : 00:80:9f:81:f4:a0 x
x Interworking with Gatekeeper + NO x
x Gatekeeper ID : -1 x
x Numb. of sig. channels IP Phones : 0 x
x Numb. of sig. channels inter-ACT : 0 x
x IP Domain Number : 0 x
x E164 Number List Index : -1 x
x Ethernet Configuration + Autoneg. (Half and Full duplex) x
x Gateway H323 name : -------------------------------- x
x x
mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj
lqReview/Modify: Boardqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk
x x
x Node Number (reserved) : 1 x
x Shelf Address : 0 x
x Board Address : 8 x
x x
x Interface Type + INTIPA x
x Virtual board + NO x
x Serial number : -------------- x
x Usage State + Idle x
x Operational State + Disabled x
x Main/Standby State + Main (Master) x
x Country Protocol Type + Default x
x Incidents Teleservice + YES x
x IP Compression Daughter Board + 1 GIP4-1 x
x No. of Compressors for Gateway : 2 x
x No. of Compressors for IP Devices : 5 x
x x
mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj
i also connect to INTIP card by console and get below capture:
------------------------------------------------------------------
------------
Logical Board : INTIP A Boot
Physical Board : Revision 2 = AC (MPC8250 40MHz, V36, Alize V24 ca
ble)
MuP : Version 8081 Revision 1014
Boot/download version : intip _06.09 _04Jul08_13h33
------------------------------------------------------------------
------------
---> Hit ENTER key to suspend coupler boot process <--
-
INTIP:
5 sec left before starting coupler
4 sec left before starting coupler
3 sec left before starting coupler
2 sec left before starting coupler
1 sec left before starting coupler
Starting Coupler
00000005-000006C3: MngtC1cpl : WAIT FOR C1 CLOCK
00000006-000006C3: MngtC1cpl : C1 CLOCK PRESENT
00000007-000006C3: C1:start_broadcasting
00000008-000006C3: CPU found on link 6
00000009-000006C3: Board Add Rq -> CPU
0000000A-000006C4: BOARD_ADR_RSP cold in cold Init
0000000B-000006C4: ConfigIP : Discovering our IP Address
0000000C-000006CB: ConfigIP : using DSCP
0000000D-000006CB: ConfigIP : default DSCP set to 0x2E
0000000E-000006CB: ConfigIP : Start Ethernet Link ...
0000000F-000006CB: EthMon : New ethernet abilities set [ 10MBps 10
0MBps Half ]
00000010-000006CB: EthMon : Autonegociation mode will be used
00000011-000006CB: EthMon : Lauch Ethernet Phyter
00000012-000006CB: EthMon : Ethernet Phyter ready
(Unexpected) Message:00 00 49 00 02 0F 00 08 08 FE 91
(Unexpected) Message:00 00 19 00 02 0F 00 08 08 FE 88
00000013-000006CB: EthMon : Start Auto-Negotiation ...
00000014-0000085C: EthMon : Auto-Negotiation process complete (BMC
R=0x1000, PHYSTS=0xAE21) (True Auto-Negotiation)
00000015-0000085C: EthMon : Speed set to 100MBps (Auto-sense)
00000016-0000085C: EthMon : Duplex set to Half (Auto-neg)
00000017-0000085C: EthMon : Wait for Link Up ...
00000018-0000085C: EthMon : Link Up
00000019-0000085C: ConfigIP : Startup of Ethernet Link succeed
0000001A-0000085C: ConfigIP : IP Address : 192.168. 1.254
0000001B-0000085C: ConfigIP : IP Subnet Mask : 255.255.255. 0
0000001C-0000085C: ConfigIP : IP Default Router : 192.168. 1.100
0000001D-0000085D: ConfigIP : Query Default Router 192.168. 1.100
using ICMP ECHO REQUEST .....................
0000001E-000018D9: ConfigIP : Ethernet check success..........
0000001F-000020B4: ConfigIP : No response from Default Router [fsk status=0x01]
00000020-000020B4: Do not download lanpbx.cfg for role INTIP-A
00000021-000020B4: Simulate lanpbx.cfg for role INTIP-A
00000022-000020B4: created lanpbx file contents TYPE=A4400 VERSION=1 IP_DOWNLOAD=192.168.1.100 IP_CPU1=192.168.1.100
00000023-000020B4: LANPBX : SEARCH OF THE GOOD CPU FROM LANPBX.CFG
00000024-000020B4: LANPBX : contents of the line 1 of lanpbx.cfg :
00000025-000020B4: IP_DOWNLOAD= 192.168.1.100
00000026-000020B4: IP_DOWNLOAD_RD= None
00000027-000020B4: IP_CPU1= 192.168.1.100
00000028-000020B4: IP_CPU2= None
00000029-000020B4: BININTIP : Download of the binary [Current size limit : 1024KBytes]
0000002A-000020B4: SEARCH FOR CPU : Try to start with cpu 192.168.1.100 (tftp client number 0 try to download file 'binintip')
------------------------------------------------------------------------------
IP Configuration Menu
------------------------------------------------------------------------------
Configuration menu not available on INTIPA board !
Available commands :
Reset Reset coupler
Use ? or ? <cmd> to get help on command
Config:
Confimenu
Config:config
Config:help
Config:
0000002B-00005389: SEARCH FOR CPU : cpu 192.168.1.100 deny INTIP board (tftp server return error = 11)
0000002C-00005389: : "No Error Message"
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
INTIP fails to start
Event : CPU search step failed
Diagnosis :
- INTIP board failed to locate the main CPU.
Checklist :
- Check lanpbx.cfg file content
- Check that Ethernet address and Crystal number are declared in database of the CPU
- Check that the CPU can ping INTIP board when this message is just displayed
Can Experts help me on this ?
