INT-IP2 card not work

Post by **vad** » 29 Jun 2010 23:28

Usually not necessary to create lanpbx file. At first - you have
"0000001D-0000085D: ConfigIP : Query Default Router 192.168. 1.100
using ICMP ECHO REQUEST .....................
0000001E-000018D9: ConfigIP : Ethernet check success..........
0000001F-000020B4: ConfigIP : No response from Default Router [fsk status=0x01]"
Connect (instead of INTIP) PC with address 192.168. 1.254 and try to ping CPU.

Next one - show "netadmin -m", menu 2 (global view) (do you have the same netmask on CPU, role IP addressing, security activated).

And last (at this moment) - if you change CPU address - you need restart (for tftp services working).

Post by **frank** » 29 Jun 2010 23:36

Here is your error

0000002B-00005389: SEARCH FOR CPU : cpu 192.168.1.100 deny INTIP board (tftp server return error = 11)

Send the result of the commands:
twin
more /etc/hosts
ifconfig -a
more /usr4/mao/lanpbx.cfg

doublevand981 · Post by **doublevand981** » 29 Jun 2010 23:59

dear Frank and Vad,
below is results as your requests:

(1)viscohn> twin

Wed Jun 30 10:51:55 CEST 2010

Usage : twin [Redundancy Cpu Enable (y/n)]

Role and CPU positions:

Role of the CPU : MAIN

CPU position : 06

CPU address : 192.168.1.100

Twin CPU position : UNKNOWN

Twin CPU address : UNKNOWN

Redundancy State:

Duplicated configuration : NO

Transmission CPU-CPU : KO

Telephony redundancy : KO

monitel redundancy : KO

memloader redundancy : KO

All applications redundancy : KO

(1)viscohn> more etc/hosts
etc/hosts: No such file or directory
(1)viscohn> ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:80:9F:74:D0:97
inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:29944 errors:0 dropped:0 overruns:0 frame:0
TX packets:3601 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:5 Base address:0xb000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:728 errors:0 dropped:0 overruns:0 frame:0
TX packets:728 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0

(1)viscohn> more /usr4/mao/lanpbx.cfg
/usr4/mao/lanpbx.cfg: No such file or directory

(1)viscohn> netadmin -m

Alcatel e-Mediate IP Network Administration
===========================================

1. 'Installation'
2. 'Show current configuration'
3. 'Local Ethernet interface'
4. 'CPU redundancy'
5. 'Role addressing'
6. 'Serial links (PPP)'
7. 'Tunnel'
8. 'Routing'
9. 'Host names and addresses'
10. 'Copy setup'
11. 'Security'
12. 'DHCP configuration'
13. 'SNMP configuration'
14. 'VLan configuration'
15. 'Node configuration'
16. 'Ethernet redundancy'
17. 'History of last actions'
18. 'Apply modifications'
0. 'Quit'

What is your choice ? 2

Your system hasn't any site number.
Private IP addressing space: no
Restricted internet accesses: no
Accept ICMP redirect: yes
Low dynamic ports range configuration : 10000 - 10499

There is no VLan configuration. No frame will be 802.1q-tagged.
The ethernet redundancy is not supported on this CPU type
node name : node000000
internal name resolver activated : no

Ethernet interface setup
========================

Netmask : 255.255.255.0

==============================================================================
| Machine type | Local interface | Name | Address |
==============================================================================
| local | Ethernet | viscohn | 192.168.1.100 |
==============================================================================

<return> to continue.

i did not use sercuritty and also tried to reset CPU some times

Post by **frank** » 30 Jun 2010 00:27

I was wrong for the lanpbx.cfg
what about:

cdmao
more lanpbx.cfg

doublevand981 · Post by **doublevand981** » 30 Jun 2010 00:34

(1)viscohn> cdmao
/DHS3data/mao
(1)viscohn> more lanpbx.cfg
lanpbx.cfg: No such file or directory

Post by **vad** » 30 Jun 2010 01:14

Check INTIP strapping (about crystal number), and was TC about INTIP not started when V24 cabel connected.

Post by **frank** » 30 Jun 2010 01:31

If lanpbx does not exist, this is your issue. Type the first command I told you before !

doublevand981 · Post by **doublevand981** » 30 Jun 2010 01:48

Dear frank,
below is results:
(1)viscohn> more /etc/hosts
10.253.253.1 xa000000
10.253.253.2 xb000000
10.253.253.3 xma000000
10.253.253.4 xmb000000
10.253.253.10 adm000000_1
10.253.253.11 adm000000_2
10.253.253.20 app000000_1
10.253.253.21 app000000_2
127.0.0.1 loopback
255.255.255.0 subnetmask
192.168.1.235 PCconfig
192.168.1.4 PCdoanh
192.168.1.15 Chaupc
192.168.1.100 viscohn maincpu standcpu node000000 localhost
(1)viscohn> ifconfig
eth0 Link encap:Ethernet HWaddr 00:80:9F:74:D0:97
inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:40229 errors:0 dropped:0 overruns:0 frame:0
TX packets:4642 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:5 Base address:0xb000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:740 errors:0 dropped:0 overruns:0 frame:0
TX packets:740 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0

(1)viscohn> ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:80:9F:74:D0:97
inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:40240 errors:0 dropped:0 overruns:0 frame:0
TX packets:4648 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:5 Base address:0xb000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:740 errors:0 dropped:0 overruns:0 frame:0
TX packets:740 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0

(1)viscohn> more /usr4/mao/lanpbx.cfg
/usr4/mao/lanpbx.cfg: No such file or directory
(1)viscohn> cdmao
/DHS3data/mao
(1)viscohn> more lanpbx.cfg
lanpbx.cfg: No such file or directory

Hi Vad,
i disconnected V24 cable.
i checked trapping with default factory. the system using 01 ACT14 shefg number 0.

Post by **vad** » 30 Jun 2010 01:56

To doublevand981 - Frank say about "lanpbxbuild -auto" command.

doublevand981 · Post by **doublevand981** » 30 Jun 2010 02:00

hi all,
below is results:

(1)viscohn> lanpbxbuild -auto

Wed Jun 30 12:59:26 CEST 2010

01. IP download: 192.168.1.100
IP CPU 1: 192.168.1.100

Are you sure (Y/N):y
Permission denied.
Permission denied.
(1)viscohn> cdmao
/DHS3data/mao
(1)viscohn> more lanpbx.cfg
lanpbx.cfg: No such file or directory
(1)viscohn> more /usr4/mao/lanpbx.cfg
/usr4/mao/lanpbx.cfg: No such file or directory
(1)viscohn>