4XX8EE Phones with Asterisk

Reinoud · Post by **Reinoud** » 19 Jul 2010 11:21

alspocky wrote:I'm trying to do the same here. I have eight Alcatel-Lucent 4018 VoIP and an Asterisk installed, but I have no idea how to start.

I'm trying to access the configuration files you are mentioning, but with no luck.

Can you help me, please?

Thanks in advance,

alspocky (fgalindo@escolessas.com)

The config files should be created by yourself and stored on the tftp server you will use to deploy the phone(s).

Take a look at the following document: IPTouchSIPphonesinstallation.pdf

alspocky · Post by **alspocky** » 19 Jul 2010 18:08

Am I correct assuming I must capture binary files from a working OmniPCX? Those named bin4018, datesip4018 and noesip4018? Some advice?

Thanks for your time!

Reinoud · Post by **Reinoud** » 20 Jul 2010 15:21

alspocky wrote:Am I correct assuming I must capture binary files from a working OmniPCX? Those named bin4018, datesip4018 and noesip4018? Some advice?

Thanks for your time!

Unless you cannot set your phone in SIP mode, you do not need an OXE. The files should be supplied with your Alcatel-Lucent reseller. These files can be put on the same tftpd server...

Again... follow the link: A-V2.01.10.7z

The bin4018 is not necessary...

MM-P · Post by **MM-P** » 18 Oct 2010 09:43

Reinoud wrote:I succeeded to get the phone to work! I activated the netlog option, and installed a syslog server. It seems that there were two parameters missing (one without value, and one completely missing). I added these parameters and it started to download and flash the phone. After that it came into service!

I´m getting also Invalid parameters after downloading sipconfig-MACADRESS.txt. I would be happy if you can send me or post your valid sipconfig-macadress.txt. I can´t find the mistake. I can´t activate netlog option on phone (pressing ok don´t work :-/)so it´s no possible to look with syslog server what´s wrong. I tried to find it out with wireshark what the problem is. But it returns only Bad Checksum ... so it´s not possible to debug

Reinoud · Post by **Reinoud** » 20 Oct 2010 12:08

MM-P wrote:I´m getting also Invalid parameters after downloading sipconfig-MACADRESS.txt. I would be happy if you can send me or post your valid sipconfig-macadress.txt. I can´t find the mistake. I can´t activate netlog option on phone (pressing ok don´t work :-/)so it´s no possible to look with syslog server what´s wrong. I tried to find it out with wireshark what the problem is. But it returns only Bad Checksum ... so it´s not possible to debug

Ok! I would love to help, but cannot until next week. I wil send you my config file. However, bad checksum sounds like something else is wrong!

MM-P · Post by **MM-P** » 22 Oct 2010 14:30

Code: Select all

10-22-2010	20:23:09	User.Error	10.0.0.201	 00:00:00 000-00:00:52.620 BCM    : EPT - HDSP: NetVHD handle 48 Unknown event 0x80c5 op1:1  op2:9212
10-22-2010	20:23:08	User.Notice	10.0.0.201	 00:00:00 000-00:00:51.660 INIT   : telnet is waiting...
10-22-2010	20:23:08	User.Notice	10.0.0.201	 00:00:00 000-00:00:51.660 INIT   : telnet is ready on port 23
10-22-2010	20:23:08	User.Notice	10.0.0.201	 00:00:00 000-00:00:51.630 INIT   : appui_set_init_screen :reset... please wait
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.630 INIT   : timezone initialised
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.630 INIT   : dns client initialised
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.630 INIT   : sipconfig_init: config polling timer '60'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.620 INIT   : sipconfig_init: binary polling timer '480'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.620 INIT   : sipconfig_init: hearing aid 'OFF'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.620 INIT   : sipconfig_init: application mode unchanged 'SIP'
10-22-2010	20:23:08	User.Notice	10.0.0.201	 00:00:00 000-00:00:51.620 ARP    : ARP_spoofing defence : defence activated
10-22-2010	20:23:08	User.Notice	10.0.0.201	 00:00:00 000-00:00:51.620 ARP    : ARP_spoofing defence : timer = 30 ms
10-22-2010	20:23:08	User.Notice	10.0.0.201	 00:00:00 000-00:00:51.620 ARP    : ARP_spoofing defence : ARP table flushed
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.610 INIT   : sipconfig_init: ARP spoofing start
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.610 INIT   : sipconfig_init: ARP spoofing timer '30'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.610 INIT   : sipconfig_init: time zone 'UT::60:032902:102503'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.610 INIT   : sipconfig_init: SNTP server address '1.de.pool.ntp.org'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.610 INIT   : sipconfig_init: domain name '10.0.0.100'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.610 INIT   : sipconfig_init: DNS2 server address '10.0.0.138'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.600 INIT   : sipconfig_init: DNS server address '10.0.0.100'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.600 INIT   : sipconfig_init: hostname 'noe_sip'
10-22-2010	20:23:08	User.Error	10.0.0.201	 00:00:00 000-00:00:51.600 BCM    : EPT - HDSP: NetVHD handle 48 Unknown event 0x80c5 op1:0  op2:9073
10-22-2010	20:23:08	User.Error	10.0.0.201	 00:00:00 000-00:00:51.590 BCM    : EPT - HDSP: NetVHD handle 48 Unknown event 0x80c5 op1:1  op2:9009
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.240 INIT   : sipconfig_init: activate VLAN filter 'no'
10-22-2010	20:23:08	User.Info	10.0.0.201	 00:00:00 000-00:00:51.240 INIT   : sipconfig_init: disable PC port 'no'
10-22-2010	20:23:08	User.Emerg	10.0.0.201	 00:00:00 000-00:00:51.240 DEFENCE: reset__: [108] sip_invalid_stand_params (859 tskinit.c)
10-22-2010	20:23:05	User.Notice	10.0.0.201	 00:00:00 000-00:00:48.240 INIT   : appui_set_init_screen :Invalid Parameters !
10-22-2010	20:23:05	User.Error	10.0.0.201	 00:00:00 000-00:00:48.230 INIT   : Checking Mandantory Parameter: supported_lang Invalid !
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.230 INIT   : Checking Mandantory Parameter: Begin
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.230 INIT   : init_dhcp_option_setting, get dns2:10.0.0.138
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.230 INIT   : init_dhcp_option_setting, get dns:10.0.0.100
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.220 INIT   : init_dhcp_option_setting, get sntp:1.de.pool.ntp.org
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.220 INIT   : init_dhcp_option_setting, get domain name:10.0.0.100
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.220 INIT   : init_dhcp_option_setting, get hostname:noe_sip
10-22-2010	20:23:05	User.Notice	10.0.0.201	 00:00:00 000-00:00:48.220 MGR    : mgr_startup: init status 3.01 success
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.220 INIT   : Updating checksum for specific config file: 1088796386
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.090 INIT   : Config file sipconfig-00809f87c731.txt successfully downloaded
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.090 TFTP   : xfer finished
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.060 TFTP   : 1st alloc   =     11424
10-22-2010	20:23:05	User.Info	10.0.0.201	 00:00:00 000-00:00:48.060 TFTP   : free memory =   9083872 bytes

I got the netlog Information finally, so here is the syslog. I think there is something wrong with the hostname, which is given in the Alcatel Dokumentation as noe_sip. But I tried also the Asterisk domainname and username.

So the device (4008) is still reseting ...

Reinoud · Post by **Reinoud** » 27 Oct 2010 07:16

MM-P,

I have attached my version of sipconfig

sipconfig-00809F8Df3E7.txt

. Have a look, it could be that there's an option missing in your file.

Let me know if it works!

MM-P · Post by **MM-P** » 27 Oct 2010 07:19

I´ve not privileges to download. So this is my 3rd post and it should work

MM-P · Post by **MM-P** » 29 Oct 2010 02:32

Thank you for your file, but it´s sth. other. Maybe it have sth. to do because there is SIP Version 1.0.30.
I´m getting still "Invalid Parameter"

Code: Select all

User.Emerg	10.0.0.201	 00:00:00 000-00:00:51.240 DEFENCE: reset__: [108] sip_invalid_stand_params (859 tskinit.c)
User.Notice	10.0.0.201	 00:00:00 000-00:00:48.240 INIT   : appui_set_init_screen :Invalid Parameters !
User.Error	10.0.0.201	 00:00:00 000-00:00:48.230 INIT   : Checking Mandantory Parameter: supported_lang Invalid !
User.Info	10.0.0.201	 00:00:00 000-00:00:48.230 INIT   : Checking Mandantory Parameter: Begin

sipconfig.txt

sipconfig-00809F87C731.txt

I can´t find the invalid parameters. I´ve attached the files. I´ve configured Asterisk in the following way:
sip.conf

Code: Select all

[general]
  context=default
  bindport=5060
  bindaddr=10.0.0.100
  srvlookup=yes
  allow=alaw
  allow=ulaw
  allow=g729
  allow=gsm
  allow=slinear
  language=de

Code: Select all

 [35]
  callerid=Office <35>
  defaultip=10.0.0.201
  domain=10.0.0.100
  user=35
  secret=
  type=friend
  mailbox=35
  nat=yes
  canreinvite=yes
  context=default

extension.conf

Code: Select all

[local]
  exten=_3X,1,NoCDR()
  exten=_3X,n,Dial,SIP/${EXTEN}|55|Ttr

The Xlite softphones are working with the configuration. So the mistage is i think on the Alcatel-Lucent 4008.

I found in an document that the parameters:
language=0 and bluetooh_parameter=blue have to be set in sipconfig.txt
... but still the same problem :-/
In the log it gives error on: Checking Mandantory Parameter: supported_lang Invalid
.. so I tried as parameter supported_lang and lang ... but still same problem :-/

Reinoud · Post by **Reinoud** » 30 Oct 2010 07:46

I'm terribly sorry, but I think I gave you the wrong file. I checked, and this

sipconfig-00809F8Df3E7.txt

should be the correct file.

I think that what I added was:
bluetooth_parameters=blue
supported_language=0

And then it worked!