H323 with Cisco

[sherif]

Hi

I tried to connect with Cisco manager with H323 without Gatekeeper
the call is not able to established and when.
I traced the call from OXE to Cisco by t3 I got this

mtracer started ...
______________________________________________________________________________
| (492531:000885) 1128: Send_IO1 (link-nbr=15, sapi=0, tei=0) :
| long: 104 desti: 0 source: 15 cryst: 0 cpl: 15 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 69
|______________________________________________________________________________
|
| [9f] Non-locking shift. codeset : 7
| [a2] EI_IP_TYPE_TERM
| [9f] Non-locking shift. codeset : 7
| IE:[05] EI_IP_INFOS (l=4) -> G711a Ece 1 Vad 0 Profil 2,
| IE:[06] UNKNOWN (l=1) d1
| [9f] Non-locking shift. codeset : 7
| IE:[07] EI_IP_QOS (l=3) b8 a0 00
| [9f] Non-locking shift. codeset : 7
| IE:[0a] EI_RTP_INFO (l=30)
| -> stop_packet=0 stop_rtp=1 h323=0 wc=0 rf=0 udp=1 rqm=0
| -> Transm_Bande=1 detection_Q23=1 dtmf_payload=96
| -> Port RTP = 32676, IPv4 : 150. 0. 0. 134.
| -> Port RTCP SR = 32677, IPv4 : 150. 0. 0. 134.
| -> Port RTCP RR = 32677, IPv4 : 150. 0. 0. 134.
| -> Port Fax = 32679, IPv4 : 150. 0. 0. 134.
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[18] CHANNEL (l=3) a8 83 81 -> T2 : No B channel
| IE:[1e] PROGRESS_ID (l=2) 80 83
| IE:[6c] CALLING_NUMBER (l=6) -> 01 81 Num : 8204
| IE:[70] CALLED_NUMBER (l=5) -> 81 Num : 8012
| IE:[7d] HLC (l=2) 91 81
| [a1] Sending complete
|______________________________________________________________________________

______________________________________________________________________________
| (492532:000887) Physical-Event :
| long: 21 desti: 0 source: 0 cryst: 0 cpl: 15 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 69
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=1) a8 -> T2 : No B channel
|______________________________________________________________________________

______________________________________________________________________________
| (492532:000888) Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 0 cpl: 15 us: 0 term: 0 type a5
| tei: 0 >>>> message received : RELEASE [4d] Call ref : 80 69
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 fe -> [fe] GOING IN CONVERSATION STATE
|______________________________________________________________________________

______________________________________________________________________________
| (492532:000889) 1146: Send_IO1 (link-nbr=15, sapi=0, tei=0) :
| long: 23 desti: 0 source: 15 cryst: 0 cpl: 15 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : REL COMP [5a] Call ref : 00 69
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=3) 81 e4 08 -> [e4] INVALID INFORMATION ELEMENT CONTENTS
|______________________________________________________________________________


so Kindly advice

[vad]

I think - for calls - you forgot to declare SD with call type IP (or not declare IP address in this SD). Absent destination IP address in your setup.

[sherif]

after adding IP in the SP I got this in T3

mtracer started ...
______________________________________________________________________________
| (592699:000986) 1147: Send_IO1 (link-nbr=15, sapi=0, tei=0) :
| long: 109 desti: 0 source: 15 cryst: 0 cpl: 15 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 74
|______________________________________________________________________________
|
| [9f] Non-locking shift. codeset : 7
| [a2] EI_IP_TYPE_TERM
| [9f] Non-locking shift. codeset : 7
| IE:[05] EI_IP_INFOS (l=9) -> G711a Ece 1 Vad 0 Profil 2, IPv4 :120.0.200.11.
| [9f] Non-locking shift. codeset : 7
| IE:[06] EI_IP_PAYLOADS (l=1) -> G729 Ece 1 Vad 0
| [9f] Non-locking shift. codeset : 7
| IE:[07] EI_IP_QOS (l=3) b8 a0 00
| [9f] Non-locking shift. codeset : 7
| IE:[0a] EI_RTP_INFO (l=30)
| -> stop_packet=0 stop_rtp=1 h323=0 wc=0 rf=0 udp=1 rqm=0
| -> Transm_Bande=1 detection_Q23=1 dtmf_payload=96
| -> Port RTP = 32684, IPv4 : 150. 0. 0. 134.
| -> Port RTCP SR = 32685, IPv4 : 150. 0. 0. 134.
| -> Port RTCP RR = 32685, IPv4 : 150. 0. 0. 134.
| -> Port Fax = 32687, IPv4 : 150. 0. 0. 134.
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[18] CHANNEL (l=3) a8 83 81 -> T2 : No B channel
| IE:[1e] PROGRESS_ID (l=2) 80 83
| IE:[6c] CALLING_NUMBER (l=6) -> 01 81 Num : 8204
| IE:[70] CALLED_NUMBER (l=5) -> 81 Num : 8012
| IE:[7d] HLC (l=2) 91 81
| [a1] Sending complete
|______________________________________________________________________________

______________________________________________________________________________
| (592699:000988) Physical-Event :
| long: 21 desti: 0 source: 0 cryst: 0 cpl: 15 us: 0 term: 0 type a5
| tei: 0 >>>> message received : CALL PROC (02) Call ref : 80 74
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=1) a8 -> T2 : No B channel
|______________________________________________________________________________

______________________________________________________________________________
| (592699:000989) Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 0 cpl: 15 us: 0 term: 0 type a5
| tei: 0 >>>> message received : RELEASE [4d] Call ref : 80 74
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 a9 -> [a9] TEMPORARY FAILURE
|______________________________________________________________________________

______________________________________________________________________________
| (592699:000990) 1144: Send_IO1 (link-nbr=15, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 0 cpl: 15 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : REL COMP [5a] Call ref : 00 74
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 81 90 -> [90] NORMAL CALL CLEARING
|______________________________________________________________________________

[Xero]

Hi i am facing the same issue with same traces when linking with Avaya...No B channel and Temporary failure ???