Page 2 of 18
Posted: 19 Jul 2010 11:21
by Reinoud
alspocky wrote:I'm trying to do the same here. I have eight Alcatel-Lucent 4018 VoIP and an Asterisk installed, but I have no idea how to start.
I'm trying to access the configuration files you are mentioning, but with no luck.
Can you help me, please?
Thanks in advance,
alspocky (
fgalindo@escolessas.com)
The config files should be created by yourself and stored on the tftp server you will use to deploy the phone(s).
Take a look at the following document:
IPTouchSIPphonesinstallation.pdf
Posted: 19 Jul 2010 18:08
by alspocky
Am I correct assuming I must capture binary files from a working OmniPCX? Those named bin4018, datesip4018 and noesip4018? Some advice?
Thanks for your time!
Posted: 20 Jul 2010 15:21
by Reinoud
alspocky wrote:Am I correct assuming I must capture binary files from a working OmniPCX? Those named bin4018, datesip4018 and noesip4018? Some advice?
Thanks for your time!
Unless you cannot set your phone in SIP mode, you do not need an OXE. The files should be supplied with your Alcatel-Lucent reseller. These files can be put on the same tftpd server...
Again... follow the link:
A-V2.01.10.7z
The bin4018 is not necessary...
Posted: 18 Oct 2010 09:43
by MM-P
Reinoud wrote:I succeeded to get the phone to work! I activated the netlog option, and installed a syslog server. It seems that there were two parameters missing (one without value, and one completely missing). I added these parameters and it started to download and flash the phone. After that it came into service!
I´m getting also Invalid parameters after downloading sipconfig-MACADRESS.txt. I would be happy if you can send me or post your valid sipconfig-macadress.txt. I can´t find the mistake. I can´t activate netlog option on phone (pressing ok don´t work :-/)so it´s no possible to look with syslog server what´s wrong. I tried to find it out with wireshark what the problem is. But it returns only Bad Checksum ... so it´s not possible to debug
Posted: 20 Oct 2010 12:08
by Reinoud
MM-P wrote:I´m getting also Invalid parameters after downloading sipconfig-MACADRESS.txt. I would be happy if you can send me or post your valid sipconfig-macadress.txt. I can´t find the mistake. I can´t activate netlog option on phone (pressing ok don´t work :-/)so it´s no possible to look with syslog server what´s wrong. I tried to find it out with wireshark what the problem is. But it returns only Bad Checksum ... so it´s not possible to debug
Ok! I would love to help, but cannot until next week. I wil send you my config file. However, bad checksum sounds like something else is wrong!
Posted: 22 Oct 2010 14:30
by MM-P
Code: Select all
10-22-2010 20:23:09 User.Error 10.0.0.201 00:00:00 000-00:00:52.620 BCM : EPT - HDSP: NetVHD handle 48 Unknown event 0x80c5 op1:1 op2:9212
10-22-2010 20:23:08 User.Notice 10.0.0.201 00:00:00 000-00:00:51.660 INIT : telnet is waiting...
10-22-2010 20:23:08 User.Notice 10.0.0.201 00:00:00 000-00:00:51.660 INIT : telnet is ready on port 23
10-22-2010 20:23:08 User.Notice 10.0.0.201 00:00:00 000-00:00:51.630 INIT : appui_set_init_screen :reset... please wait
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.630 INIT : timezone initialised
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.630 INIT : dns client initialised
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.630 INIT : sipconfig_init: config polling timer '60'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.620 INIT : sipconfig_init: binary polling timer '480'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.620 INIT : sipconfig_init: hearing aid 'OFF'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.620 INIT : sipconfig_init: application mode unchanged 'SIP'
10-22-2010 20:23:08 User.Notice 10.0.0.201 00:00:00 000-00:00:51.620 ARP : ARP_spoofing defence : defence activated
10-22-2010 20:23:08 User.Notice 10.0.0.201 00:00:00 000-00:00:51.620 ARP : ARP_spoofing defence : timer = 30 ms
10-22-2010 20:23:08 User.Notice 10.0.0.201 00:00:00 000-00:00:51.620 ARP : ARP_spoofing defence : ARP table flushed
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.610 INIT : sipconfig_init: ARP spoofing start
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.610 INIT : sipconfig_init: ARP spoofing timer '30'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.610 INIT : sipconfig_init: time zone 'UT::60:032902:102503'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.610 INIT : sipconfig_init: SNTP server address '1.de.pool.ntp.org'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.610 INIT : sipconfig_init: domain name '10.0.0.100'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.610 INIT : sipconfig_init: DNS2 server address '10.0.0.138'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.600 INIT : sipconfig_init: DNS server address '10.0.0.100'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.600 INIT : sipconfig_init: hostname 'noe_sip'
10-22-2010 20:23:08 User.Error 10.0.0.201 00:00:00 000-00:00:51.600 BCM : EPT - HDSP: NetVHD handle 48 Unknown event 0x80c5 op1:0 op2:9073
10-22-2010 20:23:08 User.Error 10.0.0.201 00:00:00 000-00:00:51.590 BCM : EPT - HDSP: NetVHD handle 48 Unknown event 0x80c5 op1:1 op2:9009
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.240 INIT : sipconfig_init: activate VLAN filter 'no'
10-22-2010 20:23:08 User.Info 10.0.0.201 00:00:00 000-00:00:51.240 INIT : sipconfig_init: disable PC port 'no'
10-22-2010 20:23:08 User.Emerg 10.0.0.201 00:00:00 000-00:00:51.240 DEFENCE: reset__: [108] sip_invalid_stand_params (859 tskinit.c)
10-22-2010 20:23:05 User.Notice 10.0.0.201 00:00:00 000-00:00:48.240 INIT : appui_set_init_screen :Invalid Parameters !
10-22-2010 20:23:05 User.Error 10.0.0.201 00:00:00 000-00:00:48.230 INIT : Checking Mandantory Parameter: supported_lang Invalid !
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.230 INIT : Checking Mandantory Parameter: Begin
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.230 INIT : init_dhcp_option_setting, get dns2:10.0.0.138
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.230 INIT : init_dhcp_option_setting, get dns:10.0.0.100
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.220 INIT : init_dhcp_option_setting, get sntp:1.de.pool.ntp.org
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.220 INIT : init_dhcp_option_setting, get domain name:10.0.0.100
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.220 INIT : init_dhcp_option_setting, get hostname:noe_sip
10-22-2010 20:23:05 User.Notice 10.0.0.201 00:00:00 000-00:00:48.220 MGR : mgr_startup: init status 3.01 success
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.220 INIT : Updating checksum for specific config file: 1088796386
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.090 INIT : Config file sipconfig-00809f87c731.txt successfully downloaded
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.090 TFTP : xfer finished
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.060 TFTP : 1st alloc = 11424
10-22-2010 20:23:05 User.Info 10.0.0.201 00:00:00 000-00:00:48.060 TFTP : free memory = 9083872 bytes
I got the netlog Information finally, so here is the syslog. I think there is something wrong with the hostname, which is given in the Alcatel Dokumentation as noe_sip. But I tried also the Asterisk domainname and username.
So the device (4008) is still reseting ...
Posted: 27 Oct 2010 07:16
by Reinoud
MM-P,
I have attached my version of sipconfig
sipconfig-00809F8Df3E7.txt
. Have a look, it could be that there's an option missing in your file.
Let me know if it works!
Posted: 27 Oct 2010 07:19
by MM-P
I´ve not privileges to download. So this is my 3rd post and it should work
Posted: 29 Oct 2010 02:32
by MM-P
Thank you for your file, but it´s sth. other. Maybe it have sth. to do because there is SIP Version 1.0.30.
I´m getting still "Invalid Parameter"
Code: Select all
User.Emerg 10.0.0.201 00:00:00 000-00:00:51.240 DEFENCE: reset__: [108] sip_invalid_stand_params (859 tskinit.c)
User.Notice 10.0.0.201 00:00:00 000-00:00:48.240 INIT : appui_set_init_screen :Invalid Parameters !
User.Error 10.0.0.201 00:00:00 000-00:00:48.230 INIT : Checking Mandantory Parameter: supported_lang Invalid !
User.Info 10.0.0.201 00:00:00 000-00:00:48.230 INIT : Checking Mandantory Parameter: Begin
sipconfig.txt
sipconfig-00809F87C731.txt
I can´t find the invalid parameters. I´ve attached the files. I´ve configured Asterisk in the following way:
sip.conf
Code: Select all
[general]
context=default
bindport=5060
bindaddr=10.0.0.100
srvlookup=yes
allow=alaw
allow=ulaw
allow=g729
allow=gsm
allow=slinear
language=de
Code: Select all
[35]
callerid=Office <35>
defaultip=10.0.0.201
domain=10.0.0.100
user=35
secret=
type=friend
mailbox=35
nat=yes
canreinvite=yes
context=default
extension.conf
Code: Select all
[local]
exten=_3X,1,NoCDR()
exten=_3X,n,Dial,SIP/${EXTEN}|55|Ttr
The Xlite softphones are working with the configuration. So the mistage is i think on the Alcatel-Lucent 4008.
I found in an document that the parameters:
language=0 and bluetooh_parameter=blue have to be set in sipconfig.txt
... but still the same problem :-/
In the log it gives error on: Checking Mandantory Parameter: supported_lang Invalid
.. so I tried as parameter supported_lang and lang ... but still same problem :-/
Posted: 30 Oct 2010 07:46
by Reinoud
I'm terribly sorry, but I think I gave you the wrong file. I checked, and this
sipconfig-00809F8Df3E7.txt
should be the correct file.
I think that what I added was:
bluetooth_parameters=blue
supported_language=0
And then it worked!