Alcatel Unleashed

Dear Colleagues,

Please help me with the following problem:

When I call from digital phone to other numbers (local, external, mobile....etc) everything is OK.
After I put receiver on-hook, release comes immediatelly.

BUT in case of analog sets, after I put receiver on-hook, release comes with DELAY, arround 2 seconds.

Please help me to exclude this DELAY.
(I need release on analog sets immediately like at digital phones).

Setting for Z boards:

Off-hook Validation Time : 12
On-hook For Rotary Valid. Time : 100
Max.Dur.Active Phase : 9
Min.Dur.Active Phase : 0
Max.Dur.Inactive Phase : 9
Min.Dur.Inactive Phase : 0
Min.Dur.InterDigit Rotary : 19
Ground Button Valid Period : 10
Filtering After On-hook Dur : 40
Min.Dur Loop Break Hookflash : 8
Max.Dur.Loop Break Hookflash : 40
Rec.Gain For QDSP : 108
Rec.Send Gain For QDSP : 160
Send Gain For QDSP : 51
GDSP Echo B9 : 0
GDSP Echo B10 : 0
GDSP Echo B11 : 0
GDSP Echo B12 : 0

Someone can correct me if I am wrong, but if the analog "on hook"were immediate would it make it impossible for the "hookflash" to function?
As soon as the hookflash was done it would go off hook.

Timers for Z board
The analoge sets release immediatelly in my Testsystem

This are the Z Board Audio Parameters Settings in my System:

Off-hook Validation Time : 12
On-hook For Rotary Valid. Time : 40
Max.Dur.Active Phase : 8
Min.Dur.Active Phase : 1
Max.Dur.Inactive Phase : 8
Min.Dur.Inactive Phase : 1
Min.Dur.InterDigit Rotary : 20
Ground Button Valid Period : 10
Filtering After On-hook Dur : 40
Min.Dur Loop Break Hookflash : 3
Max.Dur.Loop Break Hookflash : 18
Rec.Gain For QDSP : 108
Rec.Send Gain For QDSP : 160
Send Gain For QDSP : 51
GDSP Echo B9 : 0
GDSP Echo B10 : 0

I hope it will help you

regards

Any ideas?
How to exclude this DELAY for analog sets?

Dear no_wednesday I will try to modify my parameters to see the result.

Please tell me the vallue of Timer T89 (System/timers)?

89
TTESRAC
Timer for confirmation of not going on-hook (for analog sets).
To avoid the problems of ill-timed flashing.

Dear adriuja

The value of T89 is 20
Node Number (reserved) : 101
Instance (reserved) : 1
Timer No. : 89

Timer units : 20

Regards

So if I understand corectly the problem is in parameters

Min.Dur Loop Break Hookflash : 8
Max.Dur.Loop Break Hookflash : 40


And it must be changed to 3 and 18
That means Min. Dur. 0.3 sec and Max.Dur. 1.8 sec.

Am I Wright?

Min.Dur Loop Break Hookflash : 8
Max.Dur.Loop Break Hookflash : 40
On-hook For Rotary Valid. Time : 40
That means - if loop break 80 - 400 ms this is "Flash", if loop break more than 400 ms - on-hook.

But in your case you can try to decrease timer (System/ timers) 89, default 20 (2 sec).

1 Unit=100 ms
40 x 100 ms =4 sec.

Before I tried to change T89 from 20 to 10, BUT Delay remain!
(After changes I restart PABX (to validate system changes)).

Please tell me what timer introduce DELAY?