Alcatel Unleashed

HOla could help me.
I have a 6400 switch that gives me the following Log, after wanting to upgrade
U-Boot (6.3.4.265.R01) (for OS6400, OS6850, and OS6855 platforms) (Dec 15 2008 - 21:31:42)

MPC8247 Reset Status:

MPC8247 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666

CPU: MPC8247 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS6400 (Garuda)
I2C: ready
DRAM: 256 MB
FLASH: 128 MB
No environment variables found, using defaults

In: serial
Out: serial
Err: serial

No ethernet found.
Hit any key to stop autoboot: 0
## Booting image at ff900000 ...
Image Name: miniboot-6.3.4.265.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 865716 Bytes = 845.4 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Ethernet MAC address not copied to NV RAM
Loading .text @ 0x01000000 (1320444 bytes)
Loading .rodata @ 0x01142600 (275987 bytes)
Loading .data @ 0x01185c18 (122652 bytes)
Clearing .sbss @ 0x011a3b38 (1704 bytes)
Clearing .bss @ 0x011a5000 (1578044 bytes)
## Using bootline (@ 0x4200): tffs(0,0)lanswitch:default h=192.168.10.1 e=192.168.10.1:ffffff00 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff f=0x0
## Starting vxWorks at 0x01000000 ...

CS EEPROM Module ID: 42012286 , System type : 48 port 1000Base-T,with 4 combo ports,Stacking - Garuda


TFFS detected, mounting TFFS file system

Adding 5203 symbols for standalone.


Boot parameters are:

'tffs(0,0)lanswitch:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.181 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff'


AOS miniboot version: 6.3.4.265.R01
VxWorks (for Freescale MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Dec 15 2008, 21:34:02.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Freescale MPC8248. Processor #0.
Memory Size: 250 MBytes. BSP version 1.2/1.

Portions of code copyrighted by Agranat Systems, Inc. All Rights reserved
Portions of code copyrighted by Alcatel Internetworking, Inc. 1994-2008. All Rights reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999. All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991. All rights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000. All rights reserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999. All Rights reserved
Portions of code copyrighted by RSA Security, Inc. All Rights reserved
Portions of code copyrighted by Sun Micro
ystems, Inc. All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc. All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


Running fsck ....
/flash/ - Volume is OK
Attempting to load from the CERTIFIED directory...
Loading kernel from '/flash/certified/Gos.img'...
Cannot find component(alcatelNetworking_kernel.lnk) in package(/flash/certified/Gos.img)!
Cannot find component(kernel.lnk) in package(/flash/certified/Gos.img)!
Unable to load kernel image from file '/flash/certified/Gos.img'.
Unable to boot from the CERTIFIED software release.
[Miniboot]->

Hello I understand that would have to upload the files to working with Zmodem, but do not know how I could help

Hi,
from the output I see that /flash/certified is damaged.
first you can compare /flash/working and /flash/certified.
[Miniboot]->cd "/flash/certified"
[Miniboot]->ls
[Miniboot]->cd "/flash/working"
[Miniboot]->ls
If you've not seen files in /flash/working (or same files as in certified) you need Zmodem procedure.

I'm trying to make the process, but not upload any file dja me, I'm working with Putty copy what I said and switch

[Miniboot]->sysStartZmodem
Upload directory: /flash/working
rz ready to receive file, please start upload (or send 5 CTRL-X's to abort).

**B0100000023be50 "I get this straight"

hi,
the zModem procedure (sysStartZmodem) is detailed here.
Please use the search button in forum.