Set NPRAE coupler out of service
Set NPRAE coupler out of service
Is there any way I can block users from accessing any channels in the NPRAE card? I want to reset the coupler during working hours but it is really hard to get a chance because the channels are always occupied almost every second (One goes off and another one comes in).
There is no lift to success.You have to take the stairs - one at a time.
-
- Alcatel Unleashed Certified Guru
- Posts: 929
- Joined: 30 Jan 2006 09:40
- Location: Argentina
- Contact:
Re: Set NPRAE coupler out of service
Hi. If you are using ARS use ARS Routes and ARS time tables to switch communications to an other TG wich don´t have the NPRAE you want to reset. I think is the best way, it is transparent for users. Regards.
ACSE R11
OT R2.0
OT R2.0
- tot3nkopf
- Alcatel Unleashed Certified Guru
- Posts: 4058
- Joined: 02 Feb 2006 10:41
- Location: Germany & Romania
- Contact:
Re: Set NPRAE coupler out of service
Or simply set overflow through ARS.
Regards.
Regards.
Re: Set NPRAE coupler out of service
Thanks for the advise.
I thought there is a way similar to the outserv command.
I thought there is a way similar to the outserv command.
There is no lift to success.You have to take the stairs - one at a time.
- torrentula
- Alcatel Unleashed Certified Guru
- Posts: 814
- Joined: 29 Jun 2007 14:05
Re: Set NPRAE coupler out of service
Most systems have a outserv or busy channel once idle command, another feature missing from the PCX.
- Eliott_DUP
- Member
- Posts: 793
- Joined: 19 Apr 2007 11:20
- Location: In front of my PC
Re: Set NPRAE coupler out of service
I think the outserv command can be used on the ghost equipment number (cplstat) and then choose smoothly.
But incoming calls cannot be blocked...
cplstat <Crystal> <Coupler>
Read Ghost Equipment number
outserv n <Ghost Equipment number>
Disable smoothly => Yes
Maybe outserv p <Crystal> <Coupler> <Access> all can be used. Never tried...
But incoming calls cannot be blocked...
cplstat <Crystal> <Coupler>
Read Ghost Equipment number
outserv n <Ghost Equipment number>
Disable smoothly => Yes
Maybe outserv p <Crystal> <Coupler> <Access> all can be used. Never tried...
Never give up!
Re: Set NPRAE coupler out of service
the outserv command doesnt work on NPRAE unless it has been fixed recently.
Not All Those Who Wander Are Lost
- torrentula
- Alcatel Unleashed Certified Guru
- Posts: 814
- Joined: 29 Jun 2007 14:05
Re: Set NPRAE coupler out of service
I will have to give it a try, if that's the case then I retract my earlier statement.
-
- Member
- Posts: 2
- Joined: 07 Oct 2009 06:03
Re: Set NPRAE coupler out of service
There are 2 T2 access on NPRAE. Is there any way to reset one T2 without disturbing other. As in all commands like rstcpl, outserv or reinit, if you run it for one the other T2 also disturbed.
Ather PMP
Alcatel-Lucent Pakistan
Ather PMP
Alcatel-Lucent Pakistan
-
- Member
- Posts: 14
- Joined: 31 May 2011 05:42
Re: Set NPRAE coupler out of service
yes u can reset single slot of NPRAE card
use outserv p slot number a
ex. outserv p 0 11 1 a
And to inserv use
ex. inserv p 0 11 1 a
use outserv p slot number a
ex. outserv p 0 11 1 a
And to inserv use
ex. inserv p 0 11 1 a
Deepak Z.
INDIA
INDIA