6850 and I deleted certified .img files [Miniboot] ->?

[nmekasha]

Hi

I was upgrading 6850 and I deleted certified .img files. I rebooted the system accidentally and now the system is not coming up. I get [Miniboot] -> prompt. Is it any way I can copy the working directory to certified from this prompt [Miniboot] ->? Please advise.

Nebiu

[benny]

Issue the command

-> setNextRunningVersion 2

and then reload the switch (not by power off, use reboot command)

It will boot into working directory and then you can use the "copy working certified" command to put the images back into the certified directory.

Regards,
Benny

[akagi]

U-Boot (6.3.3.288.R01) (for OS6400, OS6850, and OS6855 platforms) (Nov 24 2008 -
19:09:27)

MPC8247 Reset Status: External Soft, External Hard

MPC8247 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666

CPU: MPC8247 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS6400 (Garuda)
I2C: ready
DRAM: 256 MB
FLASH: 128 MB
In: serial
Out: serial
Err: serial

No ethernet found.
Hit any key to stop autoboot: 0
## Booting image at ff900000 ...
Image Name: miniboot-6.3.3.288.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 864846 Bytes = 844.6 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Ethernet MAC address not copied to NV RAM
Loading .text @ 0x01000000 (1317152 bytes)
Loading .rodata @ 0x01141920 (276283 bytes)
Loading .data @ 0x01185060 (122004 bytes)
Clearing .sbss @ 0x011a2cf8 (1696 bytes)
Clearing .bss @ 0x011a4000 (1578044 bytes)
## Using bootline (@ 0x4200): tffs(0,0)lanswitch:default h=192.168.10.1 e=192.16
8.10.1:ffffff00 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff f=0x0
## Starting vxWorks at 0x01000000 ...
j
CS EEPROM Module ID: 42012285 , System type: 48 port 1000Base-T,with 4 Combo por
ts, Stacking - Garuda


TFFS detected, mounting TFFS file system
ol
Adding 5197 symbols for standalone.


Boot parameters are:

'tffs(0,0)lanswitch:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.
181 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff'


AOS miniboot version: 6.3.3.288.R01
VxWorks (for Freescale MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Nov 24 2008, 21:00:31.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Freescale MPC8248. Processor #0.
Memory Size: 250 MBytes. BSP version 1.2/1.

Portions of code copyrighted by Agranat Systems, Inc. All Rights reserved
Portions of code copyrighted by Alcatel Internetworking, Inc. 1994-2008. All Ri
ghts reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999. All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991. All r
ights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000. All rights r
eserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999. Al
l Rights reserved
Portions of code copyrighted by RSA Security, Inc. All Rights reserved
Portions of code copyrighted by Sun Microsystems, Inc. All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc. All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


klkll
Running fsck ....

/flash/ - Volume is OK
Attempting to load from the CERTIFIED directory...
Loading kernel from '/flash/certified/Gos.img'...
Cannot find component(alcatelNetworking_kernel.lnk) in package(/flash/certified/
Gos.img)!
Cannot find component(kernel.lnk) in package(/flash/certified/Gos.img)!
Unable to load kernel image from file '/flash/certified/Gos.img'.
Unable to boot from the CERTIFIED software release.
[Miniboot]->
[Miniboot]->