Anyone know this I know it is a key combo like the eeprom reset but cannot remember it
Thanks
how to put DECT phones in survey mode
-
Krusty65
- Alcatel Unleashed Certified Guru
- Posts: 242
- Joined: 26 Sep 2007 13:30
- Location: Normally in a comms room
Re: how to put DECT phones in survey mode
Depends on the version of handset but on the 100/200 and the 300/400 (i think)
Switch on while holding down the hang-up key and the phone book key, allow the phone to start before you release them.
Then long press on the 9 to activate the feature
Switch on while holding down the hang-up key and the phone book key, allow the phone to start before you release them.
Then long press on the 9 to activate the feature
When I was a boy of fourteen, my father was so ignorant I could hardly stand to have the old man around.
But when I got to be twenty-one, I was astonished at how much the old man had learned in seven years.
But when I got to be twenty-one, I was astonished at how much the old man had learned in seven years.
Re: how to put DECT phones in survey mode
Hi,
is it also possible to put the Mobile 500 in survey mode?
Theres no Phone-book key
is it also possible to put the Mobile 500 in survey mode?
Theres no Phone-book key
Regards,
Alf
Alf
-
rui.costa
Re: how to put DECT phones in survey mode
DECT 500 site survey mode
1 – Push [Menu] key
2 - *632*
3 – Selecct “Site survey mode”
4 – Push (OK) button
Best Regards
Rui Costa
1 – Push [Menu] key
2 - *632*
3 – Selecct “Site survey mode”
4 – Push (OK) button
Best Regards
Rui Costa
-
Avi
Re: how to put DECT phones in survey mode
Hi there,
i'm trying to flash a Mobile 500 with Flashloader Tool. It says:
Target not in boot mode
Error Code : NO_BOOT_MODE_DETECTED_ERROR
Thread end
How do i put the Device in Boot mode ?
i'm trying to flash a Mobile 500 with Flashloader Tool. It says:
Target not in boot mode
Error Code : NO_BOOT_MODE_DETECTED_ERROR
Thread end
How do i put the Device in Boot mode ?
Re: how to put DECT phones in survey mode
Handset off
Press + hold button on stick
Handset on
Hold button on stick
Click start in Flashtool
When process starts release the button on stick
The attached one is old but maybe useful. (There were the downloader not able to choose handset type but only Chip type)
Press + hold button on stick
Handset on
Hold button on stick
Click start in Flashtool
When process starts release the button on stick
The attached one is old but maybe useful. (There were the downloader not able to choose handset type but only Chip type)
You do not have the required permissions to view the files attached to this post.
-
Avi
Re: how to put DECT phones in survey mode
when trying to turn on handset while pressing the button on the stick, nothing happens on the handset, it doesn't turn on.
EDIT: And i can't start the download Tool, it says again "Not in Boot Mode"
Ideas ?
EDIT: And i can't start the download Tool, it says again "Not in Boot Mode"
Ideas ?
Re: how to put DECT phones in survey mode
Normal. Ignore it and go on. After flashing - if handset doesn't start - remove battery and plug battery again. Then try again.
see pdf Page 5
see pdf Page 5
-
Avi
Re: how to put DECT phones in survey mode
OK, found something:
Driver for Device "CP2102 USB to UART Bridge Controller" is missing. Can't find it on my system and it is not in the program directory.
Driver for Device "CP2102 USB to UART Bridge Controller" is missing. Can't find it on my system and it is not in the program directory.
Re: how to put DECT phones in survey mode
As I remember it's installed together with the SW?!Avi wrote:OK, found something:
Driver for Device "CP2102 USB to UART Bridge Controller" is missing. Can't find it on my system and it is not in the program directory.
You can try to install the DHC Software to get it. (DECT Handset Configurator) e.g. Version 2.2.6.4 - see Business Portal Download Section for Terminals.
