How to connect two Oxo's over BRA card using OSIG???HELP

[karamba]

hI

I NEED SOME INFORMATION HOW TO DO THIS CONNECTION IN TOPIC ??AND THE CONNECTION MUST BE CROSS OR STRAIGHT CABLE??
HOW TO CONFIGURE THE ARS AND OTHER PARAMETERS???

THX
mj

[tincho.rn]

Hi. you mean QSIG?. I will tell you that you have to search for information about the pin-out of the equipment you are going to connect to. Then find in the technical doc from oxo or oxe the pin-out of the bra board. Use a cable that makes RX from BRA to TX of the other equipment and TX from BRA to TX of the other equipment. As soon as you don´t have a red light in the board, you have connect the trunk phisicaly.
About configuration, I don´t know to much about OXO.
Regards.

[steve]

outputs on the BRA board: 3=TX+ 4=RX+ 5=RX- 6=TX-

You can't use MIX board with QSIG protocol !
Software license is mandatory for this feature!

Konfig:
step 1: change the protocol type in the External Line/List of Access/deatils part from EDSS1 to QSIG.
step 2: change the number of B channels from 1 to 2
step 3: set up the master/slave parameters. If you are the master, chage the Layer1/layer2 mode to network.
step 4: warm reset

step 5: Create a Trunk Group with the QSIG access, and set up the LinkCat of the trunk group.

step 6: fill up the Privat Numbering Plan. (You can menege the incoming calls from the QSIG or VoIP network in this Num plan table.)

After this step you can recive incoming calls and make outgoing calls with the trunk group prefix.

ARS konfig:
step 1: create a new line in the Internal Num PLan.
Function: Secondary Trunk Group,
Start/end: the range of the other PBXs subscribers,
Base:ARS,
NMT:keep,
Priv:Yes

Step 2: Create a new line in the ARS prefixes part.
network:Priv,
Prefix: the first digit of the other PBXs subscribers,
Range: the range of the other PBXs subscribers (without the first digit),
Substitute: the first digit of the other PBXs subscribers,
TrGpList: any free number

Step 3: Create a new line in the ARS Trunk Group List
List ID: The number from the ARS prefixes/TrGpList field
Index: the index of the real Trunk Group with the QSIG access.

Have a nice work

[karamba]

Hmmm..


i have two BRA8 cards.
First card is pluged into master node Oxo of our system. Second card BRA is pluged into our test node Oxo. I need to reset two Oxo's in the same time?? Other nodes are connected throught DLT2 cards.

The Cable connection?
TR+ <-> RX+
RX+ <-> TR+
TR- <-> RX-
RX- <-> TX-

Master/slave?

Master for example the master oxo and i have to set layer1/2 to networ mode?? The second T0 change to user??

[steve]

You need a warm reset if you:
change the type of protocoll (DSS1-->QSIG),
Change the number of B channels,
Change the Layer1/Layer2 mode

It isn't necessary to make resets at the same time.

The cable is OK.

Yes, set up the master site Layer1/layer2 Mode as network, and the other site as user.
(The user site: the clock delivery allowed is important. The priority value should be more than the clock priority of the public ISDN access.)

[karamba]

is the license to use QSIG on BRA needed???

[steve]

YES!

You need "4 additional B channels software license".
Alcatel ref. num.: 3EH03009AC

[karamba]

But i have some channels used on DLT2 board. Is there posibility to release this channels in DLT2 for BRA card??

[steve]

Yes
You can do it.