help 6850 no run

[davenigth]

WARNING: "sysResetHardwareFlag" flag is SET, forcing CMM board reset.


U-Boot 1.1.0(6.1.3.601.R01) (Sep 13 2006 - 14:37:19)

MPC8248 Reset Status: External Soft, External Hard

MPC8248 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666

CPU: MPC8248 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS68xx (Kite II)
I2C: ready
DRAM: 256 MB
FLASH: 8 MB
In: serial
Out: serial
Err: serial

No ethernet found.
IDE: Bus 0: OK
Device 0: Model: SanDisk SDCFJ-64 Firm: HDX 4.03 Ser#: 012210G1206S0200
Type: Removable Hard Disk
Capacity: 61.2 MB = 0.0 GB (125440 x 512)
USB: scanning bus for devices...
USB device not responding, giving up (status=80000000)
0 USB Devices found
Hit any key to stop autoboot: 1 0
## Booting image at ff900000 ...
Image Name: miniboot-6.1.3.601.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 781716 Bytes = 763.4 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Ethernet MAC address not copied to NV RAM
Loading .text @ 0x01000000 (1203372 bytes)
Loading .rodata @ 0x01125cb0 (242483 bytes)
Loading .data @ 0x01160fe8 (109988 bytes)
Clearing .sbss @ 0x0117bd90 (1556 bytes)
Clearing .bss @ 0x0117d000 (1818940 bytes)
## Using bootline (@ 0x4200): flash(1,0)cmm:default h=192.168.10.1 e=192.168.10.1:ffffff00 cb=115200 cp=none cs=1 cw=8 cm=modemControlOff f=0x0
## Starting vxWorks at 0x01000000 ...
ataDrv call. 0 1 24 24 621 0 0

CS EEPROM Module ID: 4201220f , System type: 48 port 1000Base-X, with 4 combo ports, stacking- kite2


Adding 4804 symbols for standalone.
Missing parameter, syntax error
Error on line 2: 'boot empgatewayipaddr
'.asciiBootParamsParse() failed.
WARNING: '/flash/boot.params' appears to be corrupt !!!
WARNING: Copying '/flash/boot.params' to '/flash/boot.params.CORRUPTED'...
WARNING: Removing '/flash/boot.params'...
Creating '/flash/boot.params' with defaults.


Boot parameters are:

'flash(1,0)cmm:default e=192.168.10.1:ffffff00 h=192.168.10.1 cb=115200 cp=none cs=1 cw=8 cm=modemControlOff'


AOS miniboot version: 6.1.3.601.R01
VxWorks (for Alcatel CMM MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Sep 13 2006, 14:39:14.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Alcatel CMM MPC8248. Processor #0.
Memory Size: 0xfa00000 (250 MB). BSP version 1.2/1.

Portions of code copyrighted by Agranat Systems, Inc. All Rights reserved
Portions of code copyrighted by Alcatel Internetworking, Inc. 1994-2006. All Rights reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999. All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991. All rights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000. All rights reserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999. All Rights reserved
Portions of code copyrighted by RSA Security, Inc. All Rights reserved
Portions of code copyrighted by Sun Microsystems, Inc. All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc. All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


Missing parameter, syntax error
Error on line 2: 'boot empgatewayipaddr
'.Missing parameter, syntax error
Error on line 2: 'boot empgatewayipaddr
'.Missing parameter, syntax error
Error on line 2: 'boot empgatewayipaddr
'.Attempting to load from the CERTIFIED directory...
Loading kernel from '/flash/certified/K2os.img'...
Cannot find component(alcatelNetworking_kernel.lnk) in package(/flash/certified/K2os.img)!
Cannot find component(kernel.lnk) in package(/flash/certified/K2os.img)!
Unable to load kernel image from file '/flash/certified/K2os.img'.
Unable to boot from the CERTIFIED software release.
[Miniboot]->reboot
WARNING: "sysResetHardwareFlag" flag is SET, forcing CMM board reset.


U-Boot 1.1.0(6.1.3.601.R01) (Sep 13 2006 - 14:37:19)

MPC8248 Reset Status: External Soft, External Hard

MPC8248 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666

CPU: MPC8248 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS68xx (Kite II)
I2C: ready
DRAM: 256 MB
FLASH: 8 MB
In: serial
Out: serial
Err: serial

No ethernet found.
IDE: Bus 0: OK
Device 0: Model: SanDisk SDCFJ-64 Firm: HDX 4.03 Ser#: 012210G1206S0200
Type: Removable Hard Disk
Capacity: 61.2 MB = 0.0 GB (125440 x 512)
USB: scanning bus for devices...
USB device not responding, giving up (status=80000000)
0 USB Devices found
Hit any key to stop autoboot: 1 0
=>

[devnull]

interrupt boot process and try to boot from working (if the files exist there) or do a xmodem recovery - there are guides here in the board