Alcatel Unleashed

Hi Alcatel Engineers

I am unable to install chorus R6.0.1 to VMware, i have try a lod but bad luck, getting error (cannot open TFTP connection)
Appreciate if someone could explain me the problem.




Regards
Afeef

Hi afeef,

U have to select company network not a direct cable from pc installer go thro below link it can help u out...Appliance server is not working try with Blade server am sure it will work,

After u select the company network, u have to put the Vmware Mac address in the Ethernet address field..

http://slimphony.blogspot.com/2006/10/o ... setup.html

cheers

Hi Sera

Thank you for your comment
I have setup all as your suggestion, i have select Bland Sever, and company Network and VMware Mac in the Ethernet address. but bad luck getting same error. i cannot attached the scrren shot in this Thread but i will sand you the screen shot.

Regards
Afeef

Hi Engineers,

I have try to install chorus R6.0.1 in my vmware. I have followed "Http:\\Slimphony site recommendation step by step in that website.

But when I press apply on PC-installer getting following error.

PXE-E11 ARP timeout.
PXE-38 TFTP connection not started.
PXE-E53 no boot filename received.

Appreciate if someone could help me to solve this problem

Regards
Afeef

HI afeef,

it should be a simple process, u knew that u have to select Blade or appliance server and company network then put ethernet mac adress on the pc installer

then make sure u have selceted the c:/ from pc installer and under c:/ check dhs3mgr folder u have created.then copy the versions under dhs3mgr, there should not be anyother folder like example

c:/dhs3mgr/h1301/h1301 it should be c:/dhs3mgr/h1301

if above options are fine with u after u click apply on the pc installer check from task manager go to process tftp and dhcp process are running or not

make sure only one network adapter is working, if u have wireless switch off & network adapter just configure the ip address and subnet no need to configure the gateway or dns if u have it remove and check it out...
Hope this will help u...i am running Vm ware 6.5.1 with out any issues,

cheers,
Pandian

Pandian, Thank you very much.

I will try and let you know.

Thanks
Afeef

Pandian

I have flowed by procedure as your advice but i cant load chorus in my VMware. when i press Apply on PC installer getting error (DHCPD file_receive failure from eth0)

Regards
Afeef

Hi Alcatel Engineers.

Can someone please help me to solve flowing problem?

I am trying more then 3 weeks to install chorus R6.1.1 on VMware 7.x.x. but still unable to solve the problem.
when i install VMware in my PC it's automatically install 2 network adapter like vmnet-1 and vmnet-2
im my pc have 1 in-build lan connection and other 2 lan card 1 is ADSL other card i am using for programming OXO and OXE pabx.

In-build lan card address is, 192.168.4.12
and ADSL lan address is, 192.168.1.3
Pabx programming lan card address is 192.168.53.100
VMnet-1 address is 192.168.153.1
VMnet-2 address is 192.168.247.1

PC Installer setup is
Call Server type: Blade Sever.
Call handling version: F1603.
Country mv
Installation type Standard.
Network type: Company network.
Network interface: 192.168.153.1
IP address: 192.168.153.2
Ethernet address: 00:0c:29:aef8

when i press Apply from PC-installer getting error like.
(DHCPD produced following error message: receive packet failed on eth1 connection reset by peer)

i have attached the screen shot.

Regards
Afeef

Problem solved install PCinstaller R2.17 everything working ok now. thank you all

do you have any idea why VMware has two virtual adapters when we installed and which one is usable ?